СИСТЕМА ECD, Diagnostic DTC:P0683

DTC Code DTC Name
P0683 Glow Plug Control Module 1 to PCM Communication Circuit

DESCRIPTION

Refer to DTC P052F.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0683 Glow Plug Control Module 1 to PCM Communication Circuit

When glow plug controller assembly and ECM cannot communicate via LIN communication.

(3 trip detection logic)

  • Open or short in LIN circuit

  • Glow plug controller assembly

  • ECM

 Does not come on DTC stored

WIRING DIAGRAM

Refer to DTC P052F.

Click here

CAUTION / NOTICE / HINT

Note


  • When replacing the ECM, the ECM needs registration and initialization.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (GLOW PLUG CONTROLLER ASSEMBLY - ECM)


    1. Disconnect connectors of the glow plug controller assembly.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B227-3 (SI) - B220-74 (LIN) Always Below 1 Ω
      B227-3 (SI) or B220-74 (LIN) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  2. REPLACE GLOW PLUG CONTROLLER ASSEMBLY


    1. Replace the glow plug controller assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  3. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


      Powertrain > Engine and ECT > Trouble Codes

    8. Confirm that the DTC is not output again.

      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  4. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 6 Click here

  5. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.

      Result
      Proceed to
      NEXT

    NEXT

  6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Engine and ECT / Trouble Codes.


      Powertrain > Engine and ECT > Trouble Codes

    8. Confirm that the DTC is not output again.

      Result
      Proceed to
      NEXT

    NEXT

    END