СИСТЕМА ECD, Diagnostic DTC:P0003, P0004

DTC Code DTC Name
P0003 Fuel Volume Regulator Control Circuit Low
P0004 Fuel Volume Regulator Control Circuit High

DESCRIPTION

Refer to DTC P0001.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0003 Fuel Volume Regulator Control Circuit Low

Short to ground in fuel quantity control valve circuit for 0.1 seconds.

(3 trip detection logic)

  • Open or short in fuel quantity control valve (fuel supply pump assembly) circuit

  • Fuel quantity control valve (fuel supply pump assembly)

  • ECM

 Does not come on DTC stored
P0004 Fuel Volume Regulator Control Circuit High

Short to power source in fuel quantity control valve circuit for 0.1 seconds or more

(1 trip detection logic)

  • Open or short in fuel quantity control valve (fuel supply pump assembly) circuit

  • Fuel quantity control valve (fuel supply pump assembly)

  • ECM

 Comes on DTC stored
Related Data List
DTC No. Data List

P0003

P0004

  • Target Common Rail Pressure

  • Common Rail Pressure

  • Quantity Regulation Valve - Current Value from Common Rail

WIRING DIAGRAM

Refer to DTC P0001.

Click here

CAUTION / NOTICE / HINT

Note


  • When replacing the ECM, the ECM needs registration and initialization.

    Click here

  • After replacing the fuel supply pump assembly, the ECM needs initialization.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the tester display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. INSPECT FUEL SUPPLY PUMP ASSEMBLY (FUEL QUANTITY CONTROL VALVE)


    1. Inspect the fuel quantity control valve (fuel supply pump assembly).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FUEL SUPPLY PUMP ASSEMBLY (FUEL QUANTITY CONTROL VALVE) Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (FUEL QUANTITY CONTROL VALVE - ECM)


    1. Disconnect the fuel quantity control valve connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B230-2 (PCV) - B220-30 (PCV) Always Below 1 Ω
      B230-2 (PCV) or B220-30 (PCV) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    GO TO STEP 7 Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (POWER SOURCE)

    A0030PIC02
    *a

    Front view of wire harness connector

    (to Fuel Quantity Control Valve)

    1. Disconnect the fuel quantity control valve connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      B230-1 (+B) - Body ground Ignition switch ON 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (FUEL QUANTITY CONTROL VALVE - EFI MAIN RELAY) Click here

    OK

  4. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 9 Click here

  5. CHECK HARNESS AND CONNECTOR (FUEL QUANTITY CONTROL VALVE - EFI MAIN RELAY)


    1. Disconnect the fuel quantity control valve connector.

    2. Remove the EFI MAIN relay from the engine room relay block and junction block.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B230-1 (+B) - 3 (EFI MAIN relay holder) Always Below 1 Ω
      B230-1 (+B) or 3 (EFI MAIN relay holder) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  6. CHECK ECM POWER SOURCE CIRCUIT


    1. Check the ECM power source circuit.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 9 Click here

  7. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 9 Click here

  8. REPLACE FUEL SUPPLY PUMP ASSEMBLY (FUEL QUANTITY CONTROL VALVE)


    1. Replace the fuel supply pump assembly.

      Click here

    2. Perform supply pump learning value reset.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  9. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    8. Confirm that the DTC is not output again.

      Result
      Proceed to
      NEXT

    NEXT

    END