СИСТЕМА SFI, Diagnostic DTC:P001100, P001200

DTC Code DTC Name
P001100 Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1
P001200 Camshaft Position "A" - Timing Over-Retarded Bank 1

DESCRIPTION

Refer to DTC P001013.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P001100 Camshaft Position "A" - Timing Over-Advanced or System Performance Bank 1 Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic).

  • Valve timing

  • Cam timing oil control solenoid assembly (for intake camshaft)

  • Camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft])

  • Camshaft timing gear assembly

  • Oil control valve filter

  • ECM

 Comes on DTC stored

SAE Code:

P0011
P001200 Camshaft Position "A" - Timing Over-Retarded Bank 1 Intake valve timing is stuck at a certain value when in the retard range (1 trip detection logic).

  • Valve timing

  • Cam timing oil control solenoid assembly (for intake camshaft)

  • Camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft])

  • Camshaft timing gear assembly

  • Oil control valve filter

  • ECM

 Comes on DTC stored

SAE Code:

P0012

MONITOR DESCRIPTION

The ECM optimizes the intake valve timing using the Variable Valve Timing (VVT) system to control the intake camshaft. The VVT system includes the ECM, cam timing oil control solenoid assembly (for intake camshaft), camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) and camshaft timing gear assembly. The ECM sends a target duty-cycle control signal to the cam timing oil control solenoid assembly (for intake camshaft). The camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) is operated to control the oil pressure supplied to the camshaft timing gear assembly based on this signal. The camshaft timing gear assembly can advance or retard the intake camshaft.

If the difference between the target and actual intake valve timing is large, and changes in the actual intake valve timing are small, the ECM interprets this as the camshaft timing gear assembly stuck malfunction and stores a DTC.

Example:

DTC P001100 is stored when the following conditions are met:


DTC P001200 is stored when the following conditions are met:


These DTCs indicate that the camshaft timing gear assembly cannot operate properly due to a camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]) malfunction or the presence of foreign matter in the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]).

MONITOR STRATEGY

Required Sensors/Components (Main)

Cam timing oil control solenoid assembly (for intake camshaft)

Camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft])

Crankshaft timing gear assembly
Required Sensors/Components (Related)

Crankshaft position sensor

Camshaft position sensor

Engine coolant temperature sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A01TARLE67

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the ignition switch off and wait for at least 30 seconds.

  5. Turn the ignition switch to ON and turn the GTS on [A].

  6. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

  7. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [C].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Idle the engine for 3 minutes or more [D].

  9. Enter the following menus: Powertrain / Engine / Trouble Codes [E].

  10. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  12. Input the DTC: P001100 or P0001200.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].

  14. Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 10 to 15 times [F].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    Tech Tips

    Depress the accelerator pedal by a large amount.

  15. Idle the engine for 3 minutes or more [G].

  16. Enter the following menus: Powertrain / Engine / Trouble Codes [H].

  17. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  18. Check the DTC judgment result again.

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

WIRING DIAGRAM

Refer to DTC P001013.

Click here

CAUTION / NOTICE / HINT

Tech Tips


  • DTC P001100 or P001200 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.

  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001100 OR P001200)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTC P001100 or P001200 is output A
      DTC P001100 or P001200 and other DTCs are output B

      Tech Tips

      If any DTCs other than P001100 or P001200 are output, troubleshoot those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1 / Data List / All Data / Intake VVT Change Angle Bank 1.


      Powertrain > Engine > Active Test
      Active Test Display
      Control the Intake VVT OCV Duty Ratio Bank 1
      Data List Display
      Intake VVT Change Angle Bank 1

    5. Read the Data List while performing the Active Test with the engine idling.

      OK
      GTS Operation Data List (Intake VVT Change Angle Bank 1)
      -100% to 100% Varies by 70 DegFR or more
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT) Click here

    OK

  3. CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Turn the GTS on.

    8. Start the engine and warm it up.

    9. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    10. Enter the following menus: Powertrain / Engine / Trouble Codes.

    11. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P001100 or P001200 is output B

      Tech Tips

      DTC P001100 or P001200 may be stored when foreign matter in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. That foreign matter may then be captured by the oil filter.


    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

  4. INSPECT CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)


    1. Inspect the cam timing oil control solenoid assembly (for intake camshaft).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT) Click here

    OK

  5. INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])


    1. Inspect the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    GO TO STEP 9 Click here

    OK

  6. INSPECT OIL CONTROL VALVE FILTER

    A01TDDWC01
    *1 Oil Control Valve Filter

    1. Remove the oil control valve filter.

      Click here

    2. Check that the filter is not clogged.

      OK
      Filter is not clogged.
      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 11 Click here

    NG

    REPLACE OIL CONTROL VALVE FILTER Click here

  7. REPLACE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY (FOR INTAKE CAMSHAFT)


    1. Replace the cam timing oil control solenoid assembly (for intake camshaft).

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  8. INSPECT CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])


    1. Inspect the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]).

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 10 Click here

    NG

  9. REPLACE CAMSHAFT TIMING GEAR BOLT (CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY [FOR INTAKE CAMSHAFT])


    1. Replace the camshaft timing gear bolt (camshaft timing oil control valve assembly [for intake camshaft]).

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  10. PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Active Test / Control the Intake VVT OCV Duty Ratio Bank 1 / Data List / All Data / Intake VVT Change Angle Bank 1.


      Powertrain > Engine > Active Test
      Active Test Display
      Control the Intake VVT OCV Duty Ratio Bank 1
      Data List Display
      Intake VVT Change Angle Bank 1

    5. Read the Data List while performing the Active Test with the engine idling.

      OK
      GTS Operation Data List (Intake VVT Change Angle Bank 1)
      -100% to 100% Varies by 70 DegFR or more
      Result
      Proceed to
      OK
      NG

    OK

    END

    NG

  11. REPLACE CAMSHAFT TIMING GEAR ASSEMBLY


    1. Replace the camshaft timing gear assembly.

      Click here

      Tech Tips

      Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  12. CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Turn the GTS on.

    8. Start the engine and warm it up.

    9. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    10. Enter the following menus: Powertrain / Engine / Trouble Codes.

    11. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P001100 or P001200 is output B

    A

    END

    B

  13. CHECK ENGINE MECHANICAL SYSTEM


    1. Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

    OK

  14. CHECK WHETHER DTC OUTPUT RECURS (DTC P001100 OR P001200)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Turn the ignition switch to ON.

    7. Turn the GTS on.

    8. Start the engine and warm it up.

    9. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    10. Enter the following menus: Powertrain / Engine / Trouble Codes.

    11. Read the DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P001100 or P001200 is output B

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

    REPLACE ECM Click here