ДАТЧИК СОСТАВА ТОПЛИВОВОЗДУШНОЙ СМЕСИ (для моделей с контроллером свечей накаливания) УСТАНОВКА

PROCEDURE


  1. INSTALL AIR FUEL RATIO SENSOR (for Sensor 2)

    Tech Tips

    Perform "A/F Sensor Compensation Reset" after replacing the air fuel ratio sensor.

    Click here


    1. B0043A5C01
      *a Torque Wrench Fulcrum Length

      Using SST, install the air fuel ratio sensor to the exhaust manifold.

      SST
      09224-00011
      Torque:
      Specified tightening torque
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }

      Note

      If the air fuel ratio sensor has been struck or dropped, replace it.

      Tech Tips


      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click here

      • When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)):

        39 N*m (398 kgf*cm, 29 ft.*lbf)

    2. Engage the 3 wire harness clamps.

  2. INSTALL AIR FUEL RATIO SENSOR (for Sensor 1)

    Tech Tips

    Perform "A/F Sensor Compensation Reset" after replacing the air fuel ratio sensor.

    Click here


    1. B00426DC01
      *a Torque Wrench Fulcrum Length

      Using SST, install the air fuel ratio sensor to the exhaust manifold.

      SST
      09224-00011
      Torque:
      Specified tightening torque
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }

      Note

      If the air fuel ratio sensor has been struck or dropped, replace it.

      Tech Tips


      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click here

      • When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 255 mm (10.0 in.)):

        39 N*m (398 kgf*cm, 29 ft.*lbf)

  3. INSTALL NO. 2 ENGINE COVER BRACKET


    1. Install the No. 2 engine cover bracket with the 2 nuts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

  4. INSTALL WIRE HARNESS CLAMP BRACKET


    1. Install the wire harness clamp bracket to the No. 2 engine cover bracket with the 2 bolts.

      Torque:
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

    2. Engage the wire harness clamp.

  5. INSTALL NO. 1 WIRE HARNESS HEAT INSULATOR


    1. B0044U2

      Install the No. 1 wire harness heat insulator to the wire harness clamp bracket.

      Tech Tips

      Do not fasten the buttons.

    2. B00451FC01
      *a Air Fuel Ratio Sensor Connector
      *b Exhaust Gas Temperature Sensor Connector

      Engage the exhaust gas temperature sensor connector to the wire harness clamp bracket.

    3. Engage the 2 air fuel ratio sensor connectors to the wire harness clamp bracket.

    4. B00421XC01
      *a Air Fuel Ratio Sensor Connector
      *b Exhaust Gas Temperature Sensor Connector

      Engage the clamp.

    5. Connect the exhaust gas temperature sensor connector.

    6. Connect the 2 air fuel ratio sensor connectors.

    7. B004473

      Fasten the 2 buttons.

  6. INSTALL NO. 1 ENGINE COVER (w/ No. 1 Engine Cover)

    Click here

  7. INSTALL OUTER COWL TOP PANEL


  8. INSTALL NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL


  9. INSTALL WATER GUARD PLATE LH


  10. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Click here

  11. INSPECT FOR EXHAUST GAS LEAK

  12. PERFORM INITIALIZATION


    1. Perform "A/F Sensor Compensation Reset" after replacing an air fuel ratio sensor.

      Click here