СИСТЕМА ECD (для моделей без контроллера свечей накаливания), Diagnostic DTC:P0045, P0047, P0048

DTC Code DTC Name
P0045 Turbocharger / Supercharger Boost Control Solenoid Circuit / Open
P0047 Turbocharger/Supercharger Boost Control "A" Circuit Low
P0048 Turbocharger/Supercharger Boost Control "A" Circuit High

DESCRIPTION

These DTCs indicate that the DC motor of the turbocharger sub-assembly is malfunctioning. The ECM monitors the DC motor current to detect an open or short in the DC motor circuit. If the current meets the criteria, the ECM stores a DTC and illuminates the MIL immediately.

The DC motor is used to operate the nozzle vane of the turbocharger. The nozzle vane opens and closes to change the velocity of exhaust gases in order to control the turbo pressure. The ECM varies the duty-cycle of the DC motor in accordance with the driving conditions.

If the nozzle vane is stuck closed (DC motor stuck off), the drivability may deteriorate at wide open throttle. If the nozzle vane is stuck open (DC motor stuck on), the drivability may deteriorate at intermediate throttle or the engine power may be in sufficient.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0045 Turbocharger / Supercharger Boost Control Solenoid Circuit / Open

Open in DC motor (turbocharger sub-assembly) circuit

(1 trip detection logic)

  • Open in DC motor (turbocharger sub-assembly) circuit

  • Turbocharger sub-assembly (DC motor)

  • ECM

 Comes on DTC stored
P0047 Turbocharger/Supercharger Boost Control "A" Circuit Low

Short in DC motor (turbocharger sub-assembly) circuit

(1 trip detection logic)

  • Short in DC motor (turbocharger sub-assembly) circuit

  • Turbocharger sub-assembly (DC motor)

  • ECM

 Comes on DTC stored
P0048 Turbocharger/Supercharger Boost Control "A" Circuit High

Short in DC motor (turbocharger sub-assembly) circuit

(1 trip detection logic)

  • Short in DC motor (turbocharger sub-assembly) circuit

  • Turbocharger sub-assembly (DC motor)

  • ECM

 Comes on DTC stored
DTC Detection Drive Pattern
DTC No. DTC Detection Drive Pattern
P0045

Turn the ignition switch to ON and wait for 10 seconds

(Monitor this DTC only once per driving cycle)
P0047 Engine idling for 30 seconds
P0048

Tech Tips


  • If DTC P0045, P0047 and/or P0048 is stored, the following symptoms may appear.


    • Poor acceleration

WIRING DIAGRAM

A01M2F5E01

CAUTION / NOTICE / HINT

Note

When replacing the ECM, perform ECM Initialization and Registration.

Click here

Tech Tips


  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing a new ECM, perform all of the initialization and registration procedures for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR)


    1. Inspect turbocharger sub-assembly (DC motor).

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE TURBOCHARGER SUB-ASSEMBLY Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM)


    1. Disconnect the DC motor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B132-2 (M+) - B138-34 (M+) Always Below 1 Ω
      B132-1 (M-) - B138-33 (M-) Always Below 1 Ω
      B132-2 (M+) or B138-34 (M+) - Body ground Always 10 kΩ or higher
      B132-1 (M-) or B138-33 (M-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  3. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  4. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off.

    5. Turn the ignition switch to ON.

    6. Turn the ignition switch off and wait for 30 seconds or more.

    7. Turn the ignition switch to ON and wait for 10 seconds or more.

    8. Start the engine.

    9. Allow the engine to idle for 30 seconds or more.

    10. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    11. Confirm that the DTC is not output again.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Proceed to
      NEXT

    NEXT

    END

  5. REPAIR OR REPLACE HARNESS OR CONNECTOR

    Result
    Proceed to
    NEXT

    NEXT

    GO TO STEP 4 Click here

  6. REPLACE TURBOCHARGER SUB-ASSEMBLY


    1. Replace the turbocharger sub-assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    GO TO STEP 4 Click here