POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on 4 Windows) OPERATION CHECK


  1. CHECK WINDOW LOCK SWITCH

    A00YPQ9

    Tech Tips

    Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch is not pushed in).


    1. When the window lock switch of the power window regulator master switch assembly is pushed: Check that the front passenger and rear windows are disabled.

    2. When the window lock switch is pushed in again: Check that the front passenger and rear windows can be operated normally.

    3. CHECK MANUAL UP / DOWN FUNCTION


      1. Check that the driver door power window operates as follows:

    4. OK
      Condition Master Switch Switch Operation Power Window
      Power switch on (IG) Driver door Pulled halfway up UP (Closes)
      Pushed halfway down DOWN (Opens)
  2. Check that the front passenger door window and rear power windows operate as follows:

    OK
    Condition Regulator Switch Switch Operation Power Window

    • Power switch on (IG)

    • Window lock switch off

    Front passenger door Pulled halfway up UP (Closes)
    Pushed halfway down DOWN (Opens)
    Rear LH door Pulled halfway up UP (Closes)
    Pushed halfway down DOWN (Opens)
    Rear RH door Pulled halfway up UP (Closes)
    Pushed halfway down DOWN (Opens)
  • CHECK AUTO UP / DOWN FUNCTION


    1. Check that the driver door power window operates as follows:

      OK
      Condition Master Switch Switch Operation Power Window
      Power switch on (IG) Driver door Pulled up (One touch operation) AUTO UP (Closes)
      Pushed down (One touch operation) AUTO DOWN (Opens)
    2. Check that the front passenger door window and rear power windows operate as follows:

      OK
      Condition Regulator Switch Switch Operation Power Window

      • Power switch on (IG)

      • Window lock switch off

      Front passenger door Pulled up (One touch operation) AUTO UP (Closes)
      Pushed down (One touch operation) AUTO DOWN (Opens)
      Rear LH door Pulled up (One touch operation) AUTO UP (Closes)
      Pushed down (One touch operation) AUTO DOWN (Opens)
      Rear RH door Pulled up (One touch operation) AUTO UP (Closes)
      Pushed down (One touch operation) AUTO DOWN (Opens)
  • CHECK REMOTE MANUAL UP / DOWN FUNCTION


    1. Check that the front passenger door window and rear power windows operate as follows:

      OK
      Condition Master Switch Switch Operation Power Window

      • Power switch on (IG)

      • Window lock switch off

      Front passenger door Pulled halfway up UP (Closes)
      Pushed halfway down DOWN (Opens)
      Rear LH door Pulled halfway up UP (Closes)
      Pushed halfway down DOWN (Opens)
      Rear RH door Pulled halfway up UP (Closes)
      Pushed halfway down DOWN (Opens)
  • CHECK REMOTE AUTO UP / DOWN FUNCTION


    1. Check that the front passenger door window and rear power windows operate as follows:

      OK
      Condition Master Switch Switch Operation Power Window

      • Power switch on (IG)

      • Window lock switch off

      Front passenger door Pulled up (One touch operation) AUTO UP (Closes)
      Pushed down (One touch operation) AUTO DOWN (Opens)
      Rear LH door Pulled up (One touch operation) AUTO UP (Closes)
      Pushed down (One touch operation) AUTO DOWN (Opens)
      Rear RH door Pulled up (One touch operation) AUTO UP (Closes)
      Pushed down (One touch operation) AUTO DOWN (Opens)
  • CHECK POWER WINDOW OPERATION FUNCTION AFTER POWER SWITCH IS TURNED OFF


    1. Check that each power window can be operated with the power window regulator master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly after the power switch is turned off.

      Tech Tips

      If the window lock switch is on, the power windows cannot be operated by using power window regulator switch assembly and rear power window regulator switch assembly. Therefore, turn the window lock switch off before checking the window operation.

    2. Check that the key-off operation function does not operate immediately after the driver door or front passenger door is opened.

      Tech Tips

      Even if the driver door or front passenger door is opened during auto window operation while the key-off operation function is on, the window will continue operating.

    3. Check that all the power windows cannot be operated after more than approximately 43 seconds have elapsed since the power switch was turned off.

  • CHECK JAM PROTECTION FUNCTION


    1. Check the basic function.

      CAUTION:

      Do not put your fingers between the door frame and door glass to check the jam protection function. Also, prevent any part of your body from being caught during inspection.

      Tech Tips

      The jam protection function is operative during both the auto up and manual up operations while the hybrid control system is stared or the power switch is on (IG), and also for approximately 43 seconds after the power switch is turned off.


      1. Fully open the window.

      2. A00YP7FC08
        *a Check Jig
        *b Cloth

        Set a check jig wrapped with a piece of cloth near the window fully closed position.

      3. Operate the auto up or manual up function to check that the power window stops and goes down after the check jig is caught between the window and door frame, and stops when the opening reaches approximately 200 mm (7.87 in.) or approximately 5 seconds have elapsed.

        Tech Tips

        If the check jig is caught when the opening is approximately 75 mm (2.95 in.) or more, the power window goes down approximately 125 mm (4.93 in.) or until approximately 2.5 seconds elapse.

      4. While the power window is moving down, check that the door glass cannot be raised using the power window switch.

  • CHECK POWER WINDOW SWITCH LED ILLUMINATION


    1. Check the LED illumination (power window regulator master switch assembly).


      1. Check that the LEDs located in the power window regulator master switch assembly illuminate when the power switch is turned on (IG).

    2. Check the LED illumination (power window regulator switch assembly).


      1. Check that the LED located in the power window regulator switch assembly illuminates when the power switch is turned on (IG).

    3. Check the LED illumination (rear power window regulator switch assembly).


      1. Check that the LED located in each rear power window regulator switch assembly illuminates when the power switch is turned on (IG).