ROOF SUNSHADE SYSTEM Roof Sunshade does not Move by Operating Roof Sunshade Switch

DESCRIPTION

The roof sunshade ECU (sliding roof drive gear assembly) receives switch signals and drives its built-in motor.

WIRING DIAGRAM

A00YPCPE07

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • When the roof sunshade ECU (sliding roof drive gear assembly) is removed and reinstalled or replaced, it requires initialization.

    Click here

  • The roof sunshade system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to the How to Proceed with Troubleshooting procedure.

    Click here

  • When a roof sunshade ECU (sliding roof drive gear assembly) DTC is output, first perform troubleshooting for the roof sunshade ECU (sliding roof drive gear assembly) DTC.

PROCEDURE


  1. READ VALUE USING GTS


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Sliding Roof / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Sliding Roof > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Open Switch Open switch signal ON or OFF

      ON: Open switch pressed

      OFF: Open switch not pressed

      		 -
      Close Switch Close switch signal ON or OFF

      ON: Close switch pressed

      OFF: Close switch not pressed

      		 -

      Body Electrical > Sliding Roof > Data List
      Tester Display
      Open Switch
      Close Switch
      OK
      The GTS display changes according to switch operation as shown in the table.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT ROOF SUNSHADE SWITCH (MAP LIGHT ASSEMBLY) Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - AUXILIARY BATTERY AND BODY GROUND)


    1. Disconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      a1-8 (B) - Body ground power switch off 11 to 14 V
      a1-1 (IG) - Body ground Power switch on (IG) 11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      a1-12 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  3. INSPECT ROOF SUNSHADE SWITCH (MAP LIGHT ASSEMBLY)


    1. A00YN5KC01
      *a

      Component without harness connected

      (Roof Sunshade Switch (Map Light Assembly))

      Remove the roof sunshade switch (map light assembly).

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      12 (OPN) - 11 (GND) Open switch is pressed Below 1 Ω
      12 (OPN) - 11 (GND) Open switch is not pressed 10 kΩ or higher
      13 (CLS) - 11 (GND) Close switch is pressed Below 1 Ω
      13 (CLS) - 11 (GND) Close switch is not pressed 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE ROOF SUNSHADE SWITCH (MAP LIGHT ASSEMBLY) Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - ROOF SUNSHADE SWITCH (MAP LIGHT ASSEMBLY) AND BODY GROUND)


    1. Disconnect the O8 roof sunshade switch (map light assembly) connector.

    2. Disconnect the a1 roof sunshade ECU (sliding roof drive gear assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      a1-5 (CLOSE) - O8-13 (CLS) Always Below 1 Ω
      a1-5 (CLOSE) - Body ground Always 10 kΩ or higher
      a1-7 (OPEN) - O8-12 (OPN) Always Below 1 Ω
      a1-7 (OPEN) - Body ground Always 10 kΩ or higher
      O8-11 (GND) - Body ground Always Below 1 Ω
      a1-12 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR