LOWER INSTRUMENT PANEL REMOVAL

PROCEDURE


  1. PRECAUTION

    Click here

  2. REMOVE UPPER INSTRUMENT PANEL ASSEMBLY

    Click here

  3. REMOVE CONSOLE BOX ASSEMBLY

    Click here

  4. REMOVE FRONT DOOR SCUFF PLATE LH

    Click here

  5. REMOVE COWL SIDE TRIM BOARD LH

    Click here

  6. REMOVE LOWER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. A01KR2L

      Disengage the 8 clips.

    2. Disconnect each connector and remove the lower instrument cluster finish panel assembly.

  7. REMOVE NO. 2 SWITCH HOLE BASE (for LHD)


    1. A01KTQB

      Disengage the 3 clips and remove the No. 2 switch hole base as shown in the illustration.

  8. REMOVE NO. 2 SWITCH HOLE BASE (for RHD)


    1. A01KRXI

      Disengage the 4 clips as shown in the illustration.

    2. Disconnect the connector and remove the No. 2 switch hole base.

  9. REMOVE NO. 1 SWITCH HOLE BASE (for LHD)


    1. A01KRJX

      Disengage the 4 clips as shown in the illustration.

    2. Disconnect the connector and remove the No. 1 switch hole base.

  10. REMOVE NO. 1 SWITCH HOLE BASE (for RHD)


    1. A01KSSI

      Disengage the 4 clips as shown in the illustration.

    2. Disconnect the connector and remove the No. 1 switch hole base.

  11. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Instrument Panel Under Cover)


    1. A01KSPN

      Remove the 2 screws <E>.

    2. A01KSSW

      Disengage the claw and guide, and remove the No. 1 instrument panel under cover sub-assembly.

  12. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  13. REMOVE STEREO OPENING COVER WITH BRACKET (w/o Radio Receiver)


    1. A01KT6X

      Remove the 4 bolts <B>.

    2. Disengage the 2 guides.

    3. Disconnect the connector and remove the stereo opening cover with bracket.

  14. REMOVE RADIO RECEIVER ASSEMBLY WITH BRACKET (w/ Radio Receiver)

    Click here

  15. REMOVE CENTER INSTRUMENT PANEL SAFETY PAD RETAINER WITH AIR CONDITIONING CONTROL ASSEMBLY

    Click here

  16. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  17. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure as for the LH side.

  18. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Instrument Panel Under Cover)


    1. A01KT7Q

      Disengage the 3 claws and guide and remove the No. 2 instrument panel under cover sub-assembly.

  19. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


    1. A01KSDLC02
      *1 Glove Compartment Door Stopper Sub-assembly
      *a Stopper

      Disengage the claw and release the glove compartment door stopper sub-assembly.

    2. Slightly bend the stoppers in the directions indicated by the arrows (A) and (B) in the illustration and pull the glove compartment door assembly until the stoppers are released.

    3. A01KSJUC01
      *a Close
      *b Open Approximately 53°

      Open the glove compartment door assembly to approximately 53° from its closed position. Pull it horizontally as shown in the illustration to disengage the 2 hinges and remove the glove compartment door assembly.

      Note

      Pulling the glove compartment door assembly upward to remove it causes the hinges to deform. Be sure to pull out the glove compartment door assembly horizontally.

  20. REMOVE GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY


    1. A01KR3P

      Disengage the claw and remove the glove compartment door stopper sub-assembly.

  21. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01KTD6

      Disengage the claw and 2 guides and disconnect the hood lock control lever sub-assembly.

  22. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. Disengage each clamp.

      A01KR6FC01
      *1 Room Temperature Sensor (Cooler Thermistor) - -
      *a DLC3 - -

    2. Disconnect each connector.

    3. Disengage the 2 claws and disconnect the DLC3.

    4. Disengage the 2 claws and disconnect the room temperature sensor (cooler thermistor).

    5. Remove the 2 bolts <A>, 8 screws <C>, screw <D> and lower instrument panel sub-assembly.

      A01KRGHC02
      *a Bolt <A> *b Screw <C>
      *c Screw <D> - -