REAR SEAT ASSEMBLY(for Hatchback) REASSEMBLY

PROCEDURE

INSTALL BENCH TYPE REAR SEAT CUSHION COVER
1. Temporarily install the bench type rear seat cushion cover to the bench type rear seat cushion pad.
2. Using hog ring pliers, install 24 new hog rings.
  Note
  
  Be careful not to damage the bench type rear seat cushion cover.
  
  Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the bench type rear seat cushion cover.
3. Using hog ring pliers, install 32 new hog rings.
  Note
  
  Be careful not to damage the bench type rear seat cushion cover.
  
  Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the bench type rear seat cushion cover.
INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (for RH Side)
1. Engage the 2 guides.
2. Install the rear seat lock control lever sub-assembly RH with the screw.
  
  Torque:
  
  2.0 N*m { 20 kgf*cm, 18 in.*lbf }
INSTALL REAR SEATBACK LOCK ASSEMBLY RH (for RH Side)
1. Engage the lock clip as shown in the illustration.
2. Install the rear seatback lock assembly RH with the 2 bolts.
  
  Torque:
  
  24 N*m { 245 kgf*cm, 18 ft.*lbf }
INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY (for RH Side)
INSTALL SEPARATE TYPE REAR SEATBACK COVER RH (for RH Side)
1. Temporarily install the separate type rear seatback cover RH to the separate type rear seatback pad RH.
2. w/o Center Armrest:
  1. Using hog ring pliers, install the separate type rear seatback cover RH to the separate type rear seatback pad RH with 7 new hog rings.
    
    Note
    
    Be careful not to damage the separate type rear seatback cover RH.
    
    Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover RH.
3. w/ Center Armrest:
  1. Using hog ring pliers, install the separate type rear seatback cover RH to the separate type rear seatback pad RH with 7 new hog rings.
    
    Note
    
    Be careful not to damage the separate type rear seatback cover RH.
    
    Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover RH.
INSTALL SEATBACK COVER WITH PAD (for RH Side)
1. Pass the rear center seat outer belt assembly through the seatback cover with pad as shown in the illustration.
2. Engage the 2 guides and 2 claws to install the rear seat shoulder belt cover.
3. Engage the 4 claws to install the 2 rear seat headrest supports.
4. w/ Center Headrest:
  1. Engage the 4 claws to install the 2 rear seat headrest supports.
5. Engage the 2 hooks.
6. Engage the 3 hooks.
7. Close the fastener as shown in the illustration.
8. Engage the 2 clips.
9. *a Fastener
  
  Engage the 2 fasteners as shown in the illustration.
10. Install the 3 clips.
INSTALL REAR SEATBACK LOCK BEZEL RH (for RH Side)
1. Engage the 5 claws to install a new rear seatback lock bezel RH.
INSTALL SEAT BELT ANCHOR COVER CAP (for RH Side)
1. Engage the 2 claws to install the seat belt anchor cover cap.
INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (w/ Center Armrest)
1. Install the bush as shown in the illustration.
2. Engage the pin as indicated by the arrows, in the order shown in the illustration.
3. Install the rear seat center armrest assembly with the bush and bolt.
  
  Torque:
  
  6.0 N*m { 61 kgf*cm, 53 in.*lbf }
INSTALL CENTER ARMREST HINGE COVER (w/ Center Armrest)
1. Engage the claw to install the center armrest hinge cover as shown in the illustration.
INSTALL REAR SEATBACK COVER (for RH Side)
1. Engage the 4 claws to install the rear seatback cover.
INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH (for RH Side)
1. Install the rear seat inner with center belt assembly RH to the rear center seat outer belt assembly with the washer.
INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (for LH Side)

Tech Tips

Use the same procedure as for the RH side.
INSTALL REAR SEATBACK LOCK ASSEMBLY LH (for LH Side)

Tech Tips

Use the same procedure as for the RH side.
INSTALL SEPARATE TYPE REAR SEATBACK COVER LH (for LH Side)
1. Temporarily install the separate type rear seatback cover LH to the separate type rear seatback pad LH.
2. Using hog ring pliers, install the separate type rear seatback cover RH to the separate type rear seatback pad RH with 7 new hog rings.
  Note
  
  Be careful not to damage the separate type rear seatback cover LH.
  
  Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover LH.
INSTALL SEATBACK COVER WITH PAD (for LH Side)
1. Temporarily install the seatback cover with pad to the rear seatback frame sub-assembly as shown in the illustration.
2. Engage the 4 claws to install the 2 rear seat headrest supports.
3. Engage the 4 hooks.
4. Close the fastener as shown in the illustration.
5. Engage the 2 clips.
6. *a Fastener
  
  Engage the 2 fasteners as shown in the illustration.
7. Install the 2 clips.
INSTALL REAR SEATBACK LOCK BEZEL LH (for LH Side)

Tech Tips

Use the same procedure as for the RH side.
INSTALL REAR SEATBACK COVER (for LH Side)

Tech Tips

Use the same procedure as for the RH side.