PRE-CRASH SAFETY SYSTEM, Diagnostic DTC:C1A48

DTC Code DTC Name
C1A48 G Sensor

DESCRIPTION

The pre-crash safety city sensor receives G sensor signals from the airbag sensor assembly (yaw rate and acceleration sensor) and outputs this DTC when a G sensor malfunction signal is received.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A48 G Sensor Once 4 seconds or more have elapsed after the power switch is turned on (IG), the pre-crash safety city sensor continuously receives a G sensor malfunction signal from the airbag sensor assembly (yaw rate and acceleration sensor) for 6 second or more while the IG voltage is 10 V or more.

  • Electronically controlled brake system

  • Airbag sensor assembly (yaw rate and acceleration sensor)

  • Pre-crash safety city sensor

CAUTION / NOTICE / HINT

Note


  • When replacing the pre-crash safety city sensor, replace it with a new one and be sure to initialize the settings. If a pre-crash safety city sensor which was installed to another vehicle is used, the information stored in the pre-crash safety city sensor will not match the information from the vehicle and, as a result, a DTC may be stored.

  • If the pre-crash safety city sensor has been replaced, or the windshield glass has been replaced or removed/installed, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

    Click here

  • First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

    Click here

PROCEDURE


  1. CHECK FOR DTCS (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

    5. Check for DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      Electronically controlled brake system DTCs are not output A
      Electronically controlled brake system DTCs are output B

    B

    GO TO ELECTRONICALLY CONTROLLED BRAKE SYSTEM Click here

    A

  2. CHECK FOR DTCS


    1. Clear the DTCs.

      Click here


      Chassis > PCS/LDA/RSA/LVN > Clear DTCs

    2. Make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the system cannot detect the malfunction.

    3. Check for DTCs.

      Click here


      Chassis > PCS/LDA/RSA/LVN > Trouble Codes
      Result
      Result Proceed to
      DTC C1A48 is not output A
      DTC C1A48 is output B

    A

    USE SIMULATION METHOD TO CHECK Click here

    B

  3. REPLACE PRE-CRASH SAFETY CITY SENSOR


    1. Replace the pre-crash safety city sensor.

      Click here

    2. Perform the "Recognition Camera/Target Position Memory" and "Recognition Camera Axis Adjust" of pre-crash safety city sensor.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK FOR DTCS


    1. Clear the DTCs.

      Click here


      Chassis > PCS/LDA/RSA/LVN > Clear DTCs

    2. Make sure that the DTC detection conditions are met.

      Tech Tips

      If the detection conditions are not met, the system cannot detect the malfunction.

    3. Check for DTCs.

      Click here


      Chassis > PCS/LDA/RSA/LVN > Trouble Codes
      Result
      Result Proceed to
      DTC C1A48 is not output A
      DTC C1A48 is output B

    A

    END (PRE-CRASH SAFETY CITY SENSOR WAS DEFECTIVE)

    B

    REPLACE AIRBAG SENSOR ASSEMBLY (YAW RATE AND ACCELERATION SENSOR) Click here