SPIRAL CABLE INSTALLATION

PROCEDURE


  1. INSPECT SPIRAL CABLE SUB-ASSEMBLY

    Note

    If the steering sensor is installed to a misaligned spiral cable sub-assembly, DTCs for an abnormal steering sensor value such as DTC B1801, C1231 and C1433 will be stored and it will be impossible to correct the problem. If this happens, replace the spiral cable with sensor sub-assembly with a new one.


    1. A01KSBKC06
      A01KS39 Colored Part

      Check if the spiral cable sub-assembly is centered.

      Tech Tips

      When the spiral cable sub-assembly is centered, the part (A) is positioned at the top and the colored part shown in the illustration can be seen.

    2. If the spiral cable sub-assembly is not centered, center it.


      1. A01KRIXC08
        A01KR3W Interlock

        While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

        Note


        • When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

        • Do not turn the spiral cable sub-assembly using the airbag wire harness.

        • If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly or spiral cable with sensor sub-assembly with a new one.

      2. A01KSV8C06
        A01KS39 Colored Part
        A01KR3W Interlock

        While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly clockwise approximately 2.5 times to the position where the colored part shown in the illustration can be seen.

        Tech Tips

        The spiral cable sub-assembly can be rotated approximately 2.5 turns to both the left and right from the center.

  2. INSTALL SPIRAL CABLE SUB-ASSEMBLY


    1. A01KRWHC06
      *a Guide
      *b Pin
      *c Lock Pin

      Align the 2 pins and 2 guides, and engage the 6 claws to install the spiral cable sub-assembly to the steering sensor.

      Note


      • Do not remove the lock pin before the spiral cable sub-assembly is installed to the steering sensor.

      • Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.

      • The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the spiral cable sub-assembly to the steering sensor.

    2. Remove the lock pin from the steering sensor.

  3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  4. INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note


    • Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).

    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel with the auxiliary battery connected and the power switch on (IG).

    • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the front wheels are facing straight ahead.

    4. Set the turn signal switch to the neutral position.

      Note

      If it is not in the neutral position, the turn signal switch pin may break.

    5. Engage the 3 claws to install the spiral cable with sensor sub-assembly.

    6. Connect each connector.

  5. INSTALL STEERING COLUMN COVER

    Click here

  6. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note

    Do not adjust the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A01KTM0C03
      A01KS39 Colored Part

      Check if the spiral cable with sensor sub-assembly is centered.

      Tech Tips

      When the spiral cable with sensor sub-assembly is centered, the part indicated by (A) is positioned at the top and the colored part shown in the illustration is visible.

    4. If the spiral cable with sensor sub-assembly is not centered, center it.

      Note


      • When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

      • Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.


      1. A01KT8FC01
        *1 Interlock

        While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

      2. A01KRL8C02
        *1 Interlock
        *2 Alignment Mark
        A01KS39 Colored Part

        While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 turns to the position where the alignment marks are aligned and the colored part shown in the illustration is visible.

        Tech Tips

        The spiral cable with sensor sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.

  7. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  8. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  9. ADJUST PARKING ASSIST SYSTEM (w/ Parking Assist Monitor System)

    Click here