PUSH-BUTTON START, Diagnostic DTC:B2284

DTC Code DTC Name
B2284 Brake Signal Malfunction

DESCRIPTION

This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match.

Tech Tips

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2284 Brake Signal Malfunction The brake signal sent via direct line and the brake signal sent via CAN communication (1-trip detection logic*) do not match.

  • AM2 fuse

  • STOP fuse

  • Brake control system

  • Power management control ECU

  • Wire harness or connector

DTC Output Confirmation Operation:


  • Connect the cable to the negative (-) auxiliary battery terminal, release the brake pedal and wait 20 seconds or more. Then depress the brake pedal for 20 seconds or more.

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected

With the electrical key transmitter sub-assembly in the cabin, even if a hybrid control system start operation is performed, the hybrid control system does not start (the multi-information display message (smart warning light) is not displayed). However, the hybrid control system can be started by turning the power switch on (ACC) and then pressing and holding it.


  • If there is a malfunction when the direct line is on, the hybrid control system can be started by pressing the power switch with the brake pedal released.

  • If there is a malfunction when the direct line is off, the hybrid control system cannot be started by pressing the power switch with the brake pedal depressed.

 -

WIRING DIAGRAM

A013B2XE06

CAUTION / NOTICE / HINT

Tech Tips

Check the connector connection to the terminal to make sure that there are no abnormalities such as a loose connection, deformation, etc.

Note


  • When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The push-button start uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the push-button start after confirming that the communication systems are functioning properly.

  • Inspect the fuses of circuits related to this system before performing the following procedure.

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

Tech Tips

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2284

    Power Source Control

  • Stop Light Switch1


    ABS/VSC/TRAC

  • Stop Light SW

 -

PROCEDURE


  1. READ VALUE USING GTS (STOP LIGHT SWITCH1)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Power Source Control / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Power Source Control > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Stop Light Switch1 Stop light switch1 ON or OFF

      ON: Brake pedal depressed

      OFF: Brake pedal released

      • Use this item to determine whether the stop light switch is malfunctioning.

      • The hybrid control system cannot be started when this item is OFF.

      • When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.

      Body Electrical > Power Source Control > Data List
      Tester Display
      Stop Light Switch1
      OK
      The GTS display changes correctly in response to the brake pedal operation.
      Result
      Proceed to
      OK
      NG

    OK

    GO TO SFI SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE)

    Result
    Proceed to
    OK
    NG

    1. A01G38PC09
      *a

      Front view of wire harness connector

      (to Power Management Control ECU)

      Disconnect the E111 and E112 power management control ECU connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E111-1 (AM22) - Body ground Power switch off 11 to 14 V
      E112-7 (AM21) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

    OK

  3. CHECK HARNESS AND CONNECTOR (GROUND)

    Result
    Proceed to
    OK
    NG

    1. A01G38PC10
      *a

      Front view of wire harness connector

      (to Power Management Control ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E111-5 (E01) - Body ground Always Below 1 Ω
      E111-6 (E1) - Body ground Always Below 1 Ω
      E112-4 (E12) - Body ground Always Below 1 Ω
      E112-5 (E02) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)


    1. A0139C2C05
      *a

      Front view of wire harness connector

      (to Power Management Control ECU)

      Disconnect the A130 power management control ECU connector.

    2. Disconnect the A124 stop light switch assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A130-23 (STP) - A124-3 (L) Always Below 1 Ω
      A130-23 (STP) or A124-3 (L) - Body ground Always 10 kΩ or higher

    4. Reconnect the A124 stop light switch assembly connector.

    5. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A130-23 (STP) - Body ground Brake pedal released 1 V or less
      Brake pedal depressed 9 V or higher
      Result
      Result Proceed to
      OK (for LHD) A
      OK (for RHD) B
      NG C

    A

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    B

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR