ENTRY AND START SYSTEM(for Start Function), Diagnostic DTC:B2274

DTC Code DTC Name
B2274 ACC Monitor Malfunction

DESCRIPTION

This DTC is stored when a malfunction in the ACC output circuit is detected. The ACC output circuit is the circuit that goes from the ACC output terminal of the certification ECU (smart key ECU assembly) to the ACC relay.

Tech Tips

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2274 ACC Monitor Malfunction

Malfunction in the ACC relay circuit in the certification ECU (smart key ECU assembly) or in the external circuit (1-trip detection logic*).

Tech Tips

When the voltage at terminal ACCD is not at the standard, the system is determined to be malfunctioning.

  • ECU-B NO. 5 fuse

  • ACC relay (Instrument panel junction block assembly)

  • Certification ECU (Smart Key ECU Assembly)

  • Wire harness or connector

DTC Output Confirmation Operation:


  • Wait 10 seconds after turning the power switch on (ACC) or on (IG), and then wait another 10 seconds after turning the power switch off.

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected

  • If there is a malfunction due to the relay being stuck on, the ACC relay does not turn off even though the power switch is off.

  • If there is a malfunction due to the relay being stuck off, the ACC relay does not turn on even though the power switch is on (ACC).

Tech Tips

The power switch can be turned on (IG) and the hybrid control system can be started.

 -

WIRING DIAGRAM

A01KSVNE01

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the power switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

  • The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

  • Inspect the fuses and relays of circuits related to this system before performing the following procedure.

  • After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

  • Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

Tech Tips

Related Data List and Active Test Items
DTC No. Data List Item Active Test Item
B2274

    Power Source Control

  • ACC Relay Monitor

 -

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (POWER SOURCE)

    Result
    Proceed to
    OK
    NG

    1. A01KSZDC62
      *a

      Rear view of wire harness connector

      (to Certification ECU (Smart Key ECU Assembly))

      Disconnect the E33 certification ECU (smart key ECU assembly) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E33-2 (+B) - Body ground Power switch off 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

    OK

  2. CHECK HARNESS AND CONNECTOR (GROUND)

    Result
    Proceed to
    OK
    NG

    1. A01KSZDC63
      *a

      Rear view of wire harness connector

      (to Certification ECU (Smart Key ECU Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E33-11 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY, BODY GROUND)


    1. Disconnect the E35 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the 3D and 3C instrument panel junction block assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E35-4 (ACCD) - 3D-25 Always Below 1 Ω
      3C-9 - Body ground Always Below 1 Ω
      E35-4 (ACCD) or 3D-25 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)


    1. Remove the instrument panel junction block assembly.

      for LHD: Click here

      for RHD: Click here

      A01KSR2C02
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

      for LHD: Click here

      for RHD: Click here

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3B-1 - 3D-13 Auxiliary battery voltage not applied to terminals 3D-25 and 3C-9 10 kΩ or higher
      Auxiliary battery voltage applied to terminals 3D-25 and 3C-9 Below 1 Ω
      Result
      Result Proceed to
      OK A
      NG (for LHD) B
      NG (for RHD) C

    B

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

    C

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY Click here

    A

  5. INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


    1. A01KR30C12
      *a

      Component with harness connected

      (Certification ECU (Smart Key ECU Assembly))

      Reconnect the E35 certification ECU (smart key ECU assembly) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E35-4 (ACCD) - Body ground Power switch off → Power switch on (ACC) 1 V or less → 8.5 V or higher
      Result
      Proceed to
      OK
      NG

    OK

    END (USE SIMULATION METHOD TO CHECK) Click here

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)