ENTRY AND START SYSTEM(for Entry Function) CUSTOMIZE PARAMETERS

CUSTOMIZE ENTRY AND START SYSTEM (for Entry Function)

1. Customizing with the GTS

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the GTS on.

   4. Enter the following menus: Customize Setting / Wireless Door Lock, Entry&Start or Warning.

   5. Select the setting by referring to the table below.

      
      Wireless Door Lock

      Tester Display	Description	Default	Setting	ECU
      Hazard Answer Back	When the doors are locked by the entry lock function, the hazard warning lights flash once.	ON	0:OFF,1:ON	Main body ECU (multiplex network body ECU)
      Open Door Warning	The buzzer sounds when the lock sensor on the door outside handle assembly is touched to perform entry lock with a door open.	ON	0:OFF,1:ON	Main body ECU (multiplex network body ECU)
      Auto Lock Time	Function that regulates the interval between unlocking and automatic relocking of doors.	30 s	00:30 s,01:60 s,10:120 s	Main body ECU (multiplex network body ECU)

      
      Entry & Start

      Tester Display	Description	Default	Setting	ECU
      Park Wait Time	Function that sets the period of time (lock confirmation time) that the door is prevented from being unlocked by operating the front door outside handle assembly after an entry lock operation is performed.	2.5s	00:0.5s,01:1.5s,10:2.5s,11:5s	Certification ECU (smart key ECU assembly)
      Ignition Available Area	Function that sets the area that the key must be in before the power switch can be operated.	All	00:Front,01:All	Certification ECU (smart key ECU assembly)
      Back Door Opening Operation	Function that opens the back door when the user is carrying the electrical key transmitter sub-assembly and presses back door opener switch assembly (unlock switch)	Long	00:Long,01:Twice,10:OFF	Certification ECU (smart key ECU assembly)
      Auto Entry Cancel SW	Function that enables or disables the entry and start system.	OFF	0:OFF,1:ON	Certification ECU (smart key ECU assembly)
      Touch Activation Over Threshold	The function that limits the consecutive entry lock operation to only 2 times can be changed between Active and Not Active. When in Not Active mode, there is no limit for the number of times that the consecutive entry lock operation can be performed.*	Active	0:Active,1:Not Active	Certification ECU (smart key ECU assembly)
      Engine Start Indicator	Function that turns the smart warning light on the combination meter assembly on or off.	ON	0:OFF,1:ON	Certification ECU (smart key ECU assembly)

      
      

      • *: for LHD

      
      Warning

      Tester Display	Description	Default	Setting	ECU
      Key Low Battery Warning	Enables or disables the sounding of the buzzer when the transmitter battery is low and the power switch is turned off after being on (IG) for 20 minutes or more.	ON	0:OFF,1:ON	Certification ECU (smart key ECU assembly)

2. Customizing with the multi-display

   
   

   1. Turn the power switch on (IG).

   2. Enter the following menus: SETUP / Vehicle.

   3. Select the setting by referring to the table below.

      Display	Default	Content	Setting	Relevant ECU
      Entry and start system.	On	Function that enables or disables the entry and start system.	On or Off	Certification ECU (smart key ECU assembly)

3. Entry cancel function (manual operation)

   Tech Tips

   While the entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the power switch.

   
   

   1. The following functions are disabled when the entry and start system is canceled.

      
      

      1. Entry unlock/lock functions

      2. Push start function

      3. Key lock-in prevention function

      4. Entry warning functions

   2. When canceling the entry and start system through manual operation:

      
      

      1. Make sure the following conditions are met:

      
      

      • The power switch is off.

      • The driver door is closed.

      • The driver door is unlocked.

      2. Press the unlock switch of the electrical key transmitter sub-assembly.

      3. Open the driver door within 5 seconds of completing the step above (driver door: closed → opened).

      4. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times within 5 seconds of completing the step above.

         Note

         If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

      5. Close and open the driver door twice (driver door: open → closed → opened → closed → opened).

      6. With the driver door open, press the unlock switch of the electrical key transmitter sub-assembly 2 times.

         Note

         If the driver door is closed before or while pressing the unlock switch, the entry cancel setting mode will end.

      7. Close and open the driver door (driver door: open → closed → opened).

      8. Close the driver door within 5 seconds of completing the above step.

      9. Check that the wireless buzzer sounds twice (short beeps) to confirm that the entry and start system has been canceled.

      Tech Tips

      Finish steps 5 to 7 within 30 seconds.

   3. Perform the following procedure to restore the entry and start system to the active state from the canceled state.

      
      

      1. Perform the procedures to cancel the entry and start system again.

      2. Check that the wireless buzzer sounds once (short beep) to confirm that the entry and start system has been restored to the active state.

         Tech Tips

         
         

         • The system changes between the canceled state and the active state each time the procedure to cancel the system through manual operation is performed.

         • The buzzer sounds twice when the system changes from the active state to the canceled state, and sounds once when the system changes from the canceled state to the active state.