LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2789

DTC Code DTC Name
B2789 No Response from ID BOX

DESCRIPTION

This DTC is stored when LIN communication between the certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2789 No Response from ID BOX No communication between certification ECU (smart key ECU assembly) and ID code box (immobiliser code ECU) for 10 seconds or more.

  • ID code box (immobiliser code ECU)

  • Certification ECU (smart key ECU assembly)

  • Wire harness or connector

  • ECU-B NO. 2 fuse

WIRING DIAGRAM

A01KSBOE08
*a ECU-B NO. 2
*b Certification ECU (Smart Key ECU Assembly)
*c ID Code Box (Immobiliser Code ECU)
*d LIN Communication Line

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • If the certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU) is replaced, refer to Service Bulletin.

PROCEDURE


  1. CHECK DTC OUTPUT


    1. Clear the DTCs.

      Click here


      Body Electrical > Entry&Start > Clear DTCs

    2. Recheck for DTCs.


      Body Electrical > Entry&Start > Trouble Codes

      Tech Tips

      When DTC B2789 and B2785 are output simultaneously, perform troubleshooting for DTC B2785 first.

      Result
      Result Proceed to
      Only B2789 is output A
      DTC B2789 and B2785 are output simultaneously B

    B

    GO TO DTC B2785 Click here

    A

  2. CHECK HARNESS AND CONNECTOR (ID CODE BOX (IMMOBILISER CODE ECU) - AUXILIARY BATTERY, BODY GROUND)


    1. Disconnect the E87 ID code box (immobiliser code ECU) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E87-1 (+B) - E87-5 (GND) Power switch off 11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E87-5 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ID CODE BOX (IMMOBILISER CODE ECU))


    1. Disconnect the E116 certification ECU (smart key ECU assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E116-17 (LIN) - E87-2 (LIN1) Always Below 1 Ω
      E116-17 (LIN) - Body ground Always 10 kΩ or higher
      E87-2 (LIN1) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. REPLACE ID CODE BOX (IMMOBILISER CODE ECU)


    1. Replace the ID code box (immobiliser code ECU).

      Tech Tips

      Refer to the Service Bulletin.

      Result
      Proceed to
      NEXT

    NEXT

  5. CHECK DTC OUTPUT


    1. Clear the DTCs.

      Click here


      Body Electrical > Entry&Start > Clear DTCs

    2. Recheck for DTCs.


      Body Electrical > Entry&Start > Trouble Codes
      OK
      DTC B2789 is not output.
      Result
      Proceed to
      OK
      NG

    OK

    END (ID CODE BOX (IMMOBILISER CODE ECU) WAS DEFECTIVE)

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)