LIN COMMUNICATION SYSTEM, Diagnostic DTC:B2324

DTC Code DTC Name
B2324 Rear Door LH ECU Communication Stop

DESCRIPTION

This DTC is stored when LIN communication between the rear door window regulator assembly (for LH door) and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2324 Rear Door LH ECU Communication Stop No communication between rear door window regulator assembly (for LH door) and main body ECU (multiplex network body ECU) for 10 seconds or more.

  • Rear door window regulator assembly (for rear LH door)

  • Main body ECU (multiplex network body ECU)

  • Instrument panel junction block assembly

  • Wire harness or connector

  • DOOR R/L fuse

WIRING DIAGRAM


  1. A013B1FE43

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • When a rear door window regulator assembly is replaced or removed and reinstalled, it requires initialization.

    for Models with Jam Protection Function on 4 Windows: Click here

    for Models with Jam Protection Function on Driver Door Window Only: Click here

PROCEDURE


  1. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY


    1. Remove the instrument panel junction block assembly.

      for LHD: Click here

      for RHD: Click here

      A013B3KC12
      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      		 - -

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Tech Tips

      This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

      Standard Resistance
      Tester Connection Condition Specified Condition
      3E-29 - MB-16 (LIN2) Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY for LHD: Click here
    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY for RHD: Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - REAR DOOR WINDOW REGULATOR ASSEMBLY (for LH Door))


    1. Disconnect the K3 rear door window regulator assembly (for LH door) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3E-29 - K3-9 (LIN) Always Below 1 Ω
      K3-9 (LIN) - Body ground Always 10 kΩ or higher
      3E-29 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (REAR DOOR WINDOW REGULATOR ASSEMBLY (for LH Door) - AUXILIARY BATTERY, BODY GROUND)


    1. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      K3-2 (B) - K3-1 (GND) Power switch off 11 to 14 V

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K3-1 (GND) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. REPLACE REAR DOOR WINDOW REGULATOR ASSEMBLY (for LH Door)


    1. Replace the rear door window regulator assembly (for LH door).

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  5. CHECK DTC OUTPUT


    1. Clear the DTCs.

      Click here


      Body Electrical > Main Body > Clear DTCs

    2. Recheck for DTCs.


      Body Electrical > Main Body > Trouble Codes
      OK
      DTC B2324 is not output.
      Result
      Proceed to
      OK
      NG

    OK

    END (REAR DOOR WINDOW REGULATOR ASSEMBLY (for LH Door) WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for LHD: Click here
    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for RHD: Click here