ELECTRONICALLY CONTROLLED BRAKE SYSTEM, Diagnostic DTC:C1235/35, C1236/36, C1238/38, C1239/39, C1275/75, C1276/76, C1277/77, C1278/78

DTC Code DTC Name
C1235/35 Foreign Object is Attached on Tip of Front Speed Sensor RH
C1236/36 Foreign Object is Attached on Tip of Front Speed Sensor LH
C1238/38 Foreign Object is Attached on Tip of Rear Speed Sensor RH
C1239/39 Foreign Object is Attached on Tip of Rear Speed Sensor LH
C1275/75 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)
C1276/76 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)
C1277/77 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)
C1278/78 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DESCRIPTION

When foreign matter adheres to a speed sensor tip or speed sensor rotor, these DTCs are stored. The presence of foreign matter can be judged when an abnormal waveform is received from a sensor.

These DTCs may also be detected when a malfunction occurs in the connector terminals or wire harness of the speed sensor circuit.

DTCs C1275/75 to C1278/78 will be cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs from C1275/75 to C1278/78 are output only in Test Mode.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1235/35 Foreign Object is Attached on Tip of Front Speed Sensor RH 541

Either of the following is detected:


  1. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

  2. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.

  • Speed sensor rotor malfunction (foreign matter attached)

  • Foreign matter attached to speed sensor

  • Open or short in speed sensor

  • Open or short in wire harness

  • Improperly connected connector, deformation or corrosion of terminals

  • Resistance in speed sensor circuit

  • Skid control ECU (Brake booster with master cylinder assembly)

 ABS DTC
C1236/36 Foreign Object is Attached on Tip of Front Speed Sensor LH 542

Either of the following is detected:


  1. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

  2. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.

  • Speed sensor rotor malfunction (foreign matter attached)

  • Foreign matter attached to speed sensor

  • Open or short in speed sensor

  • Open or short in wire harness

  • Improperly connected connector, deformation or corrosion of terminals

  • Resistance in speed sensor circuit

  • Skid control ECU (Brake booster with master cylinder assembly)

 ABS DTC
C1238/38 Foreign Object is Attached on Tip of Rear Speed Sensor RH 543

Either of the following is detected:


  1. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

  2. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.

  • Speed sensor rotor malfunction (foreign matter attached)

  • Foreign matter attached to speed sensor

  • Open or short in speed sensor

  • Open or short in wire harness

  • Improperly connected connector, deformation or corrosion of terminals

  • Resistance in speed sensor circuit

  • Skid control ECU (Brake booster with master cylinder assembly)

 ABS DTC
C1239/39 Foreign Object is Attached on Tip of Rear Speed Sensor LH 544

Either of the following is detected:


  1. At a vehicle speed of 20 km/h (12 mph) or more, noise occurs on the speed sensor signal waveform for 5 seconds or more.

  2. At a vehicle speed of 10 km/h (6 mph) or more, noise occurs once per wheel revolution for 15 seconds or more.

  • Speed sensor rotor malfunction (foreign matter attached)

  • Foreign matter attached to speed sensor

  • Open or short in speed sensor

  • Open or short in wire harness

  • Improperly connected connector, deformation or corrosion of terminals

  • Resistance in speed sensor circuit

  • Skid control ECU (Brake booster with master cylinder assembly)

 ABS DTC
C1275/75 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) - Detected only during Test Mode.

  • Front speed sensor RH

  • Front speed sensor rotor RH (Front axle hub sub-assembly RH)

 ABS Test Mode DTC
C1276/76 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) - Detected only during Test Mode.

  • Front speed sensor LH

  • Front speed sensor rotor LH (Front axle hub sub-assembly LH)

 ABS Test Mode DTC
C1277/77 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) - Detected only during Test Mode.

  • Rear speed sensor RH

  • Rear speed sensor rotor RH (Rear axle hub and bearing assembly RH)

 ABS Test Mode DTC
C1278/78 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) - Detected only during Test Mode.

  • Rear speed sensor LH

  • Rear speed sensor rotor LH (Rear axle hub and bearing assembly LH)

 ABS Test Mode DTC

Tech Tips


  • DTCs C1235/35 and C1275/75 are for the front speed sensor RH.

  • DTCs C1236/36 and C1276/76 are for the front speed sensor LH.

  • DTCs C1238/38 and C1277/77 are for the rear speed sensor RH.

  • DTCs C1239/39 and C1278/78 are for the rear speed sensor LH.

WIRING DIAGRAM

Refer to DTCs C1464/31, C1465/32, C1466/33 and C1467/34.

for Front: Click here

for Rear: Click here

CAUTION / NOTICE / HINT

Note

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click here

PROCEDURE


  1. CHECK DTC


    1. Check that no speed sensor malfunction DTCs are output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes

      Tech Tips

      When C1464/31, C1465/32, C1466/33, and/or C1467/34 are output together with C1235/35, C1236/36, C1238/38, and/or C1239/39, inspect and repair the trouble areas indicated by C1464/31, C1465/32, C1466/33, and/or C1467/34 first.

      Result
      Result Proceed to
      DTCs C1235/35 and/or C1236/36 are output. A
      DTCs C1238/38 and C1239/39 are output. B
      Speed sensor malfunction DTCs (C1464/31, C1465/32, C1466/33 and/or C1467/34) are output. C

    B

    CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE) Click here

    C

    REPAIR CIRCUITS INDICATED BY OUTPUT DTCS Click here

    A

  2. CHECK FRONT SPEED SENSOR AND SENSOR ROTOR


    1. Remove the front speed sensor and the component with the sensor rotor.

      for Speed Sensor: Click here

      for Speed Sensor Rotor: Click here

    2. Check the speed sensor tip and speed sensor rotor.

      OK
      The sensor tip and rotor are free of scratches, oil, and foreign matter.

      Note


      • If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.

        If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.

      • Check the speed sensor signal after cleaning or replacement.

        Click here

      Result
      Proceed to
      OK
      NG

    NG

    CLEAN OR REPLACE FRONT SPEED SENSOR OR COMPONENT WITH SENSOR ROTOR

    OK

  3. CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - FRONT SPEED SENSOR)


    1. Install the front speed sensor and the component with the sensor rotor.

    2. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    3. Disconnect the A144 skid control ECU (brake booster with master cylinder assembly) connector.

    4. Disconnect the A91 or A92 front speed sensor connector.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RH
      Tester Connection Condition Specified Condition
      A144-18 (FR+) - A91-1 (FR+) Always Below 1 Ω
      A144-18 (FR+) - Body ground Always 10 kΩ or higher
      A91-1 (FR+) - Body ground Always 10 kΩ or higher
      A144-5 (FR-) - A91-2 (FR-) Always Below 1 Ω
      A144-5 (FR-) - Body ground Always 10 kΩ or higher
      A91-2 (FR-) - Body ground Always 10 kΩ or higher
      for LH
      Tester Connection Condition Specified Condition
      A144-31 (FL+) - A92-1 (FL+) Always Below 1 Ω
      A144-31 (FL+) - Body ground Always 10 kΩ or higher
      A92-1 (FL+) - Body ground Always 10 kΩ or higher
      A144-32 (FL-) - A92-2 (FL-) Always Below 1 Ω
      A144-32 (FL-) - Body ground Always 10 kΩ or higher
      A92-2 (FL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)


    1. A01G2S2C02
      *a

      Front view of wire harness connector

      (to Front Speed Sensor)

      Reconnect the A144 skid control ECU (brake booster with master cylinder assembly) connector.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for RH
      Tester Connection Condition Specified Condition
      A91-1 (FR+) - Body ground Power switch on (IG) 5.7 to 14 V
      for LH
      Tester Connection Condition Specified Condition
      A92-1 (FL+) - Body ground Power switch on (IG) 5.7 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY for LHD: Click here
    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY for RHD: Click here

    OK

  5. RECONFIRM DTC


    1. Turn the power switch off.

    2. Reconnect the A91 or A92 front speed sensor connector.

    3. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    4. Turn the power switch on (READY).

    5. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.

    6. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTCs C1235/35 and/or C1236/36 are output. A
      DTCs C1235/35 and C1236/36 are not output. B

    B

    USE SIMULATION METHOD TO CHECK Click here

    A

  6. REPLACE FRONT SPEED SENSOR


    1. Turn the power switch off.

    2. Replace the front speed sensor.

      Click here

      Note

      Check the speed sensor signal after replacement.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  7. RECONFIRM DTC


    1. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    2. Turn the power switch on (READY).

    3. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.

    4. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTCs C1235/35 and/or C1236/36 are output. A
      DTCs C1235/35 and C1236/36 are not output. B

    B

    END

    A

  8. REPLACE FRONT AXLE HUB SUB-ASSEMBLY


    1. Turn the power switch off.

    2. Replace the front speed sensor rotor (front axle hub sub-assembly).

      Click here

      Tech Tips

      If the front speed sensor rotor needs to be replaced, replace the front axle hub sub-assembly.

      Note

      Check the speed sensor signal after replacement.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  9. RECONFIRM DTC


    1. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    2. Turn the power switch on (READY).

    3. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.

    4. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTCs C1235/35 and/or C1236/36 are output. A
      DTCs C1235/35 and C1236/36 are not output. B

    A

    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY for LHD: Click here
    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY for RHD: Click here

    B

    END

  10. CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE)


    1. A01G32JC02
      *A for RH
      *B for LH
      *a Front view of skid control sensor wire
      *b

      Front view of wire harness connector

      (to Sensor Side Connector)
      *c

      Front view of wire harness connector

      (to Vehicle Side Connector)

      Make sure that there is no looseness at the locking part and the connecting part of the connectors.

    2. Remove the skid control sensor wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RH
      Tester Connection Condition Specified Condition
      h1-2 (RR+) - hL1-1 (RR+) Always Below 1 Ω
      h1-2 (RR+) - hL1-2 (RR-) Always 10 kΩ or higher
      h1-2 (RR+) - Body ground Always 10 kΩ or higher
      hL1-1 (RR+) - Body ground Always 10 kΩ or higher
      h1-1 (RR-) - hL1-2 (RR-) Always Below 1 Ω
      h1-1 (RR-) - hL1-1 (RR+) Always 10 kΩ or higher
      h1-1 (RR-) - Body ground Always 10 kΩ or higher
      hL1-2 (RR-) - Body ground Always 10 kΩ or higher
      for LH
      Tester Connection Condition Specified Condition
      j1-2 (RL+) - jL1-1 (RL+) Always Below 1 Ω
      j1-2 (RL+) - jL1-2 (RL-) Always 10 kΩ or higher
      j1-2 (RL+) - Body ground Always 10 kΩ or higher
      jL1-1 (RL+) - Body ground Always 10 kΩ or higher
      j1-1 (RL-) - jL1-2 (RL-) Always Below 1 Ω
      j1-1 (RL-) - jL1-1 (RL+) Always 10 kΩ or higher
      j1-1 (RL-) - Body ground Always 10 kΩ or higher
      jL1-2 (RL-) - Body ground Always 10 kΩ or higher

      Note

      Check the speed sensor signal after replacement.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SKID CONTROL SENSOR WIRE Click here

    OK

  11. CHECK HARNESS AND CONNECTOR (BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY - SKID CONTROL SENSOR WIRE)


    1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

    2. Disconnect the A144 skid control ECU (brake booster with master cylinder assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RH
      Tester Connection Condition Specified Condition
      A144-22 (RR+) - hL1-1 (RR+) Always Below 1 Ω
      A144-22 (RR+) - Body ground Always 10 kΩ or higher
      hL1-1 (RR+) - Body ground Always 10 kΩ or higher
      A144-9 (RR-) - hL1-2 (RR-) Always Below 1 Ω
      A144-9 (RR-) - Body ground Always 10 kΩ or higher
      hL1-2 (RR-) - Body ground Always 10 kΩ or higher
      for LH
      Tester Connection Condition Specified Condition
      A144-20 (RL+) - jL1-1 (RL+) Always Below 1 Ω
      A144-20 (RL+) - Body ground Always 10 kΩ or higher
      jL1-1 (RL+) - Body ground Always 10 kΩ or higher
      A144-7 (RL-) - jL1-2 (RL-) Always Below 1 Ω
      A144-7 (RL-) - Body ground Always 10 kΩ or higher
      jL1-2 (RL-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  12. INSPECT BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY (SENSOR OUTPUT)


    1. A01G3KYC06
      *a

      Front view of wire harness connector

      (to Front Speed Sensor)

      Reconnect the A144 skid control ECU (brake booster with master cylinder assembly) connector.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for RH
      Tester Connection Condition Specified Condition
      hL1-1 (RR+) - Body ground Power switch on (IG) 5.7 to 14 V
      for LH
      Tester Connection Condition Specified Condition
      jL1-1 (RL+) - Body ground Power switch on (IG) 5.7 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY for LHD: Click here
    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY for RHD: Click here

    OK

  13. RECONFIRM DTC


    1. Turn the power switch off.

    2. Install the skid control sensor wire.

    3. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    4. Turn the power switch on (READY).

    5. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.

    6. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTCs C1238/38 and/or C1239/39 are output. A
      DTCs C1238/38 and C1239/39 are not output. B

    B

    USE SIMULATION METHOD TO CHECK Click here

    A

  14. REPLACE REAR AXLE HUB AND BEARING ASSEMBLY


    1. Turn the power switch off.

    2. Replace the rear speed sensor rotor with rear speed sensor (rear axle hub and bearing assembly).

      Click here

      Tech Tips

      The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.

      If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.

      Note

      Check the speed sensor signal after replacement.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  15. RECONFIRM DTC


    1. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    2. Turn the power switch on (READY).

    3. Drive the vehicle at a speed of 20 km/h (12 mph) or more for at least 15 seconds.

    4. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTCs C1238/38 and/or C1239/39 are output. A
      DTCs C1238/38 and C1239/39 are not output. B

    A

    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY for LHD: Click here
    REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY for RHD: Click here

    B

    END