DATA LIST
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuator and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the power switch to on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / (desired system) / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Traveling Direction | Traveling direction | Not Fwd or Fwd | Not Fwd: Shift lever in R or N Fwd: Shift lever in any position other than R or N |
- |
| Headlight Low Beam State | Headlight (Low beam) condition | ON or OFF | ON: Headlights (low beam) on OFF: Headlights (low beam) off |
- |
| Headlight High Beam State | Headlight (High beam) condition | ON or OFF | ON: Headlights (high beam) on OFF: Headlights (high beam) off |
- |
| Engine | Engine condition | Run or Stop | Run: Engine running Stop: Engine stopped |
- |
| +B | IG power supply voltage value | 0.00 to 19.75 V | 11.00 to 14.00 V | - |
| FR Wheel Speed | Front right wheel speed | 0.00 to 327.67 km/h (203.61 mph) | Condition can be displayed | - |
| FL Wheel Speed | Front left wheel speed | 0.00 to 327.67 km/h (203.61 mph) | Condition can be displayed | - |
| Vehicle Speed | Vehicle speed | 0.00 to 327.67 km/h (203.61 mph) | Condition can be displayed | - |
| Number Of Trouble Codes | Number of trouble codes recorded | 0 to 255 | - | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Dimmer SW | Dimmer switch high position signal | ON or OFF | ON: Dimmer switch in high or high flash position OFF: Dimmer switch in low position |
- |
| Auto Light SW | Light control switch AUTO position signal | ON or OFF | ON: Light control switch in AUTO position OFF: Light control switch not in AUTO position |
- |
| Head Light SW (Head) | Light control switch head position signal | ON or OFF | ON: Light control switch in head position OFF: Light control switch not in head position |
- |
| Illumination Rate Info | Illumination rate information | 0.00 ms. to 2162.65 ms. | Value is output according to ambient light levels | - |
| Auto H Beam STS0 | Automatic high beam sensor current state | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | - |
| Auto H Beam STS1 | Automatic high beam sensor state past 1 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | - |
| Auto H Beam STS2 | Automatic high beam sensor state past 2 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | - |
| Auto H Beam STS3 | Automatic high beam sensor state past 3 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | - |
| Auto H Beam STS4 | Automatic high beam sensor state past 4 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | - |
| Auto H Beam STS5 | Automatic high beam sensor state past 5 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | - |
| Auto H Beam STS6 | Automatic high beam sensor state past 6 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | - |
| Auto H Beam STS7 | Automatic high beam sensor state past 7 | Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | - |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / AFS / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Automatic High Beam Operation | Automatic high beam system operation | ON/OFF | ON: Operation is started OFF: Operation is stopped |
Tech Tips
Use the following procedure for operation check.
Change the Active Test item to ON and check that the inner rear view mirror assembly indicator blinks.
Make the area around the vehicle dark enough for the automatic high beam system to turn on and check that the high beam headlights turn on.
With the high beam headlights on, shine a light on the camera lens of the inner rear view mirror assembly (automatic high beam sensor) using a white or red light and check that the high beam headlights change to the low beam headlights.
Note
The low beam or high beam headlights may not turn on if the area around the vehicle is bright or depending on the way that light is shone on the camera lens.