POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Driver Door Window Only) Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

DESCRIPTION

When the power switch is on (IG), the front door window regulator assembly (for passenger door) is operated by the power window regulator switch assembly.

WIRING DIAGRAM


  1. for LHD

    A013AL7E01

  2. for RHD

    A013AL7E03

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • Check that the window lock switch is off before performing the following procedure.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - AUXILIARY BATTERY)


    1. Disconnect the G9*1 or H9*2 power window regulator switch assembly connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      for LHD
      Tester Connection Condition Specified Condition
      G9-3 (B) - Body ground Power switch on (IG) 11 to 14 V
      for RHD
      Tester Connection Condition Specified Condition
      H9-3 (B) - Body ground Power switch on (IG) 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  2. INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY


    1. A0139RBC01
      *a

      Component without harness connected

      (Power Window Regulator Switch Assembly)

      Remove the power window regulator switch assembly.

      Click here

    2. Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (D) - 2 (SD) UP Below 1 Ω
      3 (B) - 4 (U) Below 1 Ω
      1 (D) - 2 (SD) Off Below 1 Ω
      4 (U) - 5 (SU) Below 1 Ω
      4 (U) - 5 (SU) DOWN Below 1 Ω
      1 (D) - 3 (B) Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT DOOR WINDOW REGULATOR ASSEMBLY (FOR PASSENGER DOOR))


    1. Disconnect the G14*1 or H10*2 front door window regulator assembly (for passenger door) connector.


      • *1: for LHD

      • *2: for RHD

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      G9-4 (U) - G14-2 (U) Always Below 1 Ω
      G9-1 (D) - G14-1 (D) Always Below 1 Ω
      G9-4 (U) - Body ground Always 10 kΩ or higher
      G9-1 (D) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      H9-4 (U) - H10-2 (U) Always Below 1 Ω
      H9-1 (D) - H10-1 (D) Always Below 1 Ω
      H9-4 (U) - Body ground Always 10 kΩ or higher
      H9-1 (D) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


    1. Remove the power window regulator master switch assembly.

      Click here

    2. A013AZ3C12
      *A w/ Rear Power Window
      *B w/o Rear Power Window
      *a

      Component without harness connected

      (Power Window Regulator Master Switch Assembly (for LHD))

      for LHD:

      Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard Resistance
      w/ Rear Power Window
      Tester Connection Condition Specified Condition
      6 (B) - 16 (U) UP Below 1 Ω
      1 (E) - 15 (D) Below 1 Ω
      1 (E) - 16 (U) Off Below 1 Ω
      1 (E) - 15 (D) Below 1 Ω
      6 (B) - 15 (D) DOWN Below 1 Ω
      1 (E) - 16 (U) Below 1 Ω
      w/o Rear Power Window
      Tester Connection Condition Specified Condition
      15 (B) - 12 (U) UP Below 1 Ω
      7 (E) - 16 (D) Below 1 Ω
      7 (E) - 12 (U) Off Below 1 Ω
      7 (E) - 16 (D) Below 1 Ω
      15 (B) - 16 (D) DOWN Below 1 Ω
      7 (E) - 12 (U) Below 1 Ω
    3. A013AZ3C13
      *A w/ Rear Power Window
      *B w/o Rear Power Window
      *a

      Component without harness connected

      (Power Window Regulator Master Switch Assembly (for RHD))

      for RHD:

      Measure the resistance when the switch is operated according to the value(s) in the table below.

      Standard Resistance
      w/ Rear Power Window
      Tester Connection Condition Specified Condition
      6 (B) - 12 (U) UP Below 1 Ω
      9 (E) - 13 (D) Below 1 Ω
      9 (E) - 12 (U) Off Below 1 Ω
      9 (E) - 13 (D) Below 1 Ω
      6 (B) - 13 (D) DOWN Below 1 Ω
      9 (E) - 12 (U) Below 1 Ω
      w/o Rear Power Window
      Tester Connection Condition Specified Condition
      15 (B) - 12 (U) UP Below 1 Ω
      7 (E) - 10 (D) Below 1 Ω
      7 (E) - 12 (U) Off Below 1 Ω
      7 (E) - 10 (D) Below 1 Ω
      15 (B) - 10 (D) DOWN Below 1 Ω
      7 (E) - 12 (U) Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - POWER WINDOW REGULATOR SWITCH ASSEMBLY)


    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD with Rear Power Window
      Tester Connection Condition Specified Condition
      H11-16 (U) - G9-5 (SU) Always Below 1 Ω
      H11-15 (D) - G9-2 (SD) Always Below 1 Ω
      H11-16 (U) - Body ground Always 10 kΩ or higher
      H11-15 (D) - Body ground Always 10 kΩ or higher
      for LHD without Rear Power Window
      Tester Connection Condition Specified Condition
      H11-12 (U) - G9-5 (SU) Always Below 1 Ω
      H11-16 (D) - G9-2 (SD) Always Below 1 Ω
      H11-12 (U) - Body ground Always 10 kΩ or higher
      H11-16 (D) - Body ground Always 10 kΩ or higher
      for RHD with Rear Power Window
      Tester Connection Condition Specified Condition
      G11-12 (U) - H9-5 (SU) Always Below 1 Ω
      G11-13 (D) - H9-2 (SD) Always Below 1 Ω
      G11-12 (U) - Body ground Always 10 kΩ or higher
      G11-13 (D) - Body ground Always 10 kΩ or higher
      for RHD without Rear Power Window
      Tester Connection Condition Specified Condition
      G11-12 (U) - H9-5 (SU) Always Below 1 Ω
      G11-10 (D) - H9-2 (SD) Always Below 1 Ω
      G11-12 (U) - Body ground Always 10 kΩ or higher
      G11-10 (D) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY (FOR PASSENGER DOOR) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR