POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Driver Door Window Only), Diagnostic DTC:B2312

DESCRIPTION

The front door window regulator assembly (for driver door) is operated by the power window regulator master switch assembly. The front door window regulator assembly (for driver door) has motor, regulator and ECU functions.

This DTC is stored when the ECU built into the front door window regulator assembly (for driver door) determines that the power window regulator master switch assembly is stuck.

WIRING DIAGRAM

1. for LHD

   

2. for RHD

   

CAUTION / NOTICE / HINT

PROCEDURE

1. CHECK DTC OUTPUT

   
   

   1. Clear the DTC.

      Click here

      
      Body Electrical > D-Door Motor > Clear DTCs

   2. Check for DTCs.

      Click here

      
      Body Electrical > D-Door Motor > Trouble Codes

      OK
      DTC B2312 is not output.

      Result
      Proceed to OK NG

   
   

   OK

   END (DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

   NG

2. READ VALUE USING GTS (D-DOOR MOTOR)

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the GTS on.

   4. Enter the following menus: Body Electrical / D-Door Motor / Data List.

   5. Read the Data List according to the display on the GTS.

      
      Body Electrical > D-Door Motor > Data List

      Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
      D Door P/W Auto SW	Driver door power window auto switch signal	ON or OFF	ON: Driver door power window auto switch being operated OFF: Driver door power window auto switch not being operated	-
      D Door P/W Up SW	Driver door power window manual up switch signal	ON or OFF	ON: Driver door power window manual up switch being operated OFF: Driver door power window manual up switch not being operated	-
      D Door P/W Down SW	Driver door power window manual down switch signal	ON or OFF	ON: Driver door power window manual down switch being operated OFF: Driver door power window manual down switch not being operated	-

      
      Body Electrical > D-Door Motor > Data List

      Tester Display
      D Door P/W Auto SW
      D Door P/W Up SW
      D Door P/W Down SW

      OK
      On the GTS screen, ON or OFF is displayed accordingly.

      Result
      Proceed to OK NG

   
   

   OK

   REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY (FOR DRIVER DOOR) Click here

   NG

3. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT DOOR WINDOW REGULATOR ASSEMBLY (FOR DRIVER DOOR))

   
   

   1. Disconnect the H11*1 or G11*2 power window regulator master switch assembly connector.

   2. Disconnect the H14*1 or G5*2 front door window regulator assembly (for driver door) connector.

      
      

      • *1: for LHD

      • *2: for RHD

   3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD Tester Connection Condition Specified Condition H11-18 (U) - Body ground Always 10 kΩ or higher H11-10 (D) - Body ground Always 10 kΩ or higher H11-1 (A) - Body ground Always 10 kΩ or higher H14-10 (UP) - Body ground Always 10 kΩ or higher H14-7 (DOWN) - Body ground Always 10 kΩ or higher H14-4 (AUTO) - Body ground Always 10 kΩ or higher
      for RHD Tester Connection Condition Specified Condition G11-9 (U) - Body ground Always 10 kΩ or higher G11-6 (D) - Body ground Always 10 kΩ or higher G11-18 (A) - Body ground Always 10 kΩ or higher G5-10 (UP) - Body ground Always 10 kΩ or higher G5-7 (DOWN) - Body ground Always 10 kΩ or higher G5-4 (AUTO) - Body ground Always 10 kΩ or higher

      Result
      Proceed to OK NG

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

4. INSPECT POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

   
   

   1. Remove the power window regulator master switch assembly.

      Click here

   2. 

      *a	Component without harness connected (Power Window Regulator Master Switch Assembly (for LHD))

      for LHD:

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 18 (U) - 7 (E) Released 10 kΩ or higher 18 (U) - 1 (A) Released 10 kΩ or higher 1 (A) - 7 (E) Released 10 kΩ or higher 10 (D) - 7 (E) Released 10 kΩ or higher 1 (A) - 10 (D) Released 10 kΩ or higher

   3. 

      *a	Component without harness connected (Power Window Regulator Master Switch Assembly (for RHD))

      for RHD:

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 9 (U) - 7 (E) Released 10 kΩ or higher 9 (U) - 18 (A) Released 10 kΩ or higher 18 (A) - 7 (E) Released 10 kΩ or higher 6 (D) - 7 (E) Released 10 kΩ or higher 18 (A) - 6 (D) Released 10 kΩ or higher

      Result
      Proceed to OK NG

   
   

   OK

   REPLACE FRONT DOOR WINDOW REGULATOR ASSEMBLY (FOR DRIVER DOOR) Click here

   NG

   REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY Click here