REAR BUMPER(for Hatchback) REASSEMBLY

PROCEDURE


  1. INSTALL REAR BUMPER ARM SUB-ASSEMBLY LH


    1. A0139GX

      Install the rear bumper arm sub-assembly LH with the 3 bolts.

      Torque:
      11.5 N*m  { 117 kgf*cm, 8 ft.*lbf }

  2. INSTALL REAR BUMPER ARM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  3. INSTALL NO. 1 REAR BUMPER REINFORCEMENT


    1. A0139FH

      Install the No. 1 rear bumper reinforcement with the 8 bolts.

      Torque:
      11.5 N*m  { 117 kgf*cm, 8 ft.*lbf }

  4. INSTALL REAR BUMPER SIDE SEAL LH


    1. A013B28

      Install the rear bumper side seal LH with the 3 clips.

  5. INSTALL REAR BUMPER SIDE SEAL RH


    1. A013AWJ

      Install the rear bumper side seal RH with the 3 clips.

  6. INSTALL UPPER REAR BUMPER RETAINER LH


    1. A013BA5

      Engage the 2 guides to temporarily install the upper rear bumper retainer LH to the rear combination light assembly LH.

    2. A0139XA

      Engage the 2 guides as shown in the illustration to temporarily install the upper rear bumper retainer LH and rear combination light assembly LH as a set.

    3. Install the upper rear bumper retainer LH with the screw.

  7. INSTALL UPPER REAR BUMPER RETAINER RH

    Tech Tips

    Use the same procedure as for the LH side.

  8. INSTALL REAR COMBINATION LIGHT ASSEMBLY LH

    Click here

  9. INSTALL REAR COMBINATION LIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  10. INSTALL REAR BUMPER SIDE RETAINER LH


    1. A013APD

      Engage the 3 claws.

    2. Install the rear bumper side retainer LH with the 2 screws.

  11. INSTALL REAR BUMPER SIDE RETAINER RH

    Tech Tips

    Use the same procedure as for the LH side.

  12. INSTALL REAR BUMPER MOULDING


    1. A013B4N

      Engage the 3 guides and 2 claws.

    2. Install the rear bumper moulding with the 3 screws.

  13. INSTALL REAR BUMPER SIDE MOULDING LH


    1. A0139V6

      Engage the 4 claws.

    2. Install the rear bumper side moulding LH with the 3 screws.

  14. INSTALL REAR BUMPER SIDE MOULDING RH

    Tech Tips

    Use the same procedure as for the LH side.

  15. INSTALL REAR BUMPER GUARD


    1. A013ATC

      Engage the 11 claws.

    2. A0139QG

      Install the rear bumper guard with the 4 screws.

      Torque:
      1.5 N*m  { 15 kgf*cm, 13 in.*lbf }

  16. INSTALL REFLEX REFLECTOR ASSEMBLY LH


    1. A013ACO

      Engage the claw.

    2. Install the reflex reflector assembly LH with the screw.

  17. INSTALL REFLEX REFLECTOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  18. INSTALL REAR LICENSE PLATE CUSHION


    1. Wipe off any tape adhesive residue with cleaner.

    2. Remove the release paper from 6 new rear license plate cushions.

      Tech Tips

      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. Install the 6 rear license plate cushions as showm in the illustration.

      A0139VPC01
      *a Line - -

      Tech Tips

      Stick the 6 rear license plate cushions on the lines marked on the rear bumper assembly.

  19. INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)


    1. A013B7C

      Engage the 2 clamps to install the No. 2 luggage room wire.

  20. INSTALL ULTRASONIC SENSOR BEZEL (w/ TOYOTA Parking Assist-sensor System)

    Click here

  21. INSTALL ULTRASONIC SENSOR CLIP (w/ TOYOTA Parking Assist-sensor System)

    Click here

  22. INSTALL NO. 3 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

    Click here