ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *A | w/ Cover | - | - |
| *1 | CENTER NO. 4 ENGINE UNDER COVER | *2 | FRONT LOWER BUMPER ABSORBER |
| *3 | FRONT NO. 3 ENGINE UNDER COVER | *4 | NO. 1 ENGINE UNDER COVER |
| *5 | REAR ENGINE UNDER COVER LH | *6 | REAR ENGINE UNDER COVER RH |
ILLUSTRATION
| *1 | AIR CLEANER CAP SUB-ASSEMBLY | *2 | AIR CLEANER CASE SUB-ASSEMBLY |
| *3 | AIR CLEANER HOSE ASSEMBLY | *4 | INLET AIR CLEANER ASSEMBLY |
| *5 | NO. 2 CYLINDER HEAD COVER | *6 | AIR CLEANER FILTER ELEMENT |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | ENGINE ROOM MAIN WIRE | *2 | FRAME WIRE |
| *3 | GENERATOR CABLE | *4 | INVERTER COVER |
| *5 | INVERTER WITH CONVERTER ASSEMBLY | *6 | MOTOR CABLE |
| *7 | NO. 1 INVERTER BRACKET | *8 | NO. 1 INVERTER COOLING HOSE |
| *9 | NO. 2 ENGINE ROOM WIRE | *10 | NO. 2 ENGINE WIRE |
| *11 | NO. 6 INVERTER COOLING HOSE | *12 | NO. 1 RELAY BLOCK COVER |
| *13 | RELAY BLOCK COVER | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FUEL TUBE SUB-ASSEMBLY | *2 | HEATER HOSE |
| *3 | INLET HEATER WATER HOSE A | *4 | INVERTER RESERVE TANK ASSEMBLY |
| *5 | INVERTER TRAY BRACKET | *6 | NO. 1 FUEL VAPOR FEED HOSE |
| *7 | NO. 1 RADIATOR HOSE | *8 | NO. 2 RADIATOR HOSE |
| *9 | NO. 3 INVERTER COOLING HOSE | *10 | NO. 4 WATER BY-PASS HOSE |
| *11 | NO. 5 INVERTER COOLING HOSE | *12 | OUTLET HEATER WATER HOSE A |
| *13 | RADIATOR PIPE | *14 | NO. 1 FUEL PIPE CLAMP |
| *15 | NO. 3 RADIATOR HOSE | *16 | FUEL PIPE |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | COLUMN HOLE COVER SILENCER SHEET | *2 | COMPRESSOR WITH MOTOR ASSEMBLY |
| *3 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *A | w/ Exhaust Heat Recirculation System | *B | w/o Exhaust Heat Recirculation System |
| *1 | FRONT CENTER FLOOR BRACE | *2 | FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst) |
| *3 | HEATER WATER HOSE | *4 | COMPRESSION SPRING |
| *5 | EXHAUST PIPE SUPPORT | *6 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *A | Type A | *B | Type B |
| *C | w/ Reinforcement | - | - |
| *1 | ENGINE FRONT MOUNTING BRACKET LOWER REINFORCEMENT | *2 | FRONT ENGINE MOUNTING INSULATOR |
| *3 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY | *4 | FRONT SUSPENSION MEMBER BRACE REAR LH |
| *5 | FRONT SUSPENSION MEMBER BRACE REAR RH | *6 | FRONT SUSPENSION MEMBER REINFORCEMENT LH |
| *7 | FRONT SUSPENSION MEMBER REINFORCEMENT RH | *8 | NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
| *9 | REAR ENGINE MOUNTING INSULATOR | *10 | FRONT CROSSMEMBER SUB-ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque |  |
Do not apply lubricants |
ILLUSTRATION
| *1 | ENGINE MOUNTING INSULATOR LH | *2 | ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
| *3 | ENGINE WIRE | *4 | RADIATOR RESERVOIR TANK ASSEMBLY |
| *5 | COOLER PIPE CLAMP BRACKET | *6 | COOLER PIPE CLAMP |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FLYWHEEL HOUSING SIDE COVER | *2 | FLYWHEEL SUB-ASSEMBLY |
| *3 | HYBRID VEHICLE TRANSAXLE ASSEMBLY | *4 | STARTER HOLE INSULATOR |
| *5 | TRANSMISSION INPUT DAMPER ASSEMBLY | *6 | ENGINE ASSEMBLY |
| *T1 | 1st: 49 (500, 36) 2nd: Turn 90° |
- | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ★ | Precoated part |