HV BATTERY REMOVAL

PROCEDURE


  1. PRECAUTION

    Click here

  2. CHECK FOR DTC


    1. Check for DTCs.

      Click here

      Note

      Confirm that P0AA6 (Hybrid Battery Voltage System Isolation Fault) is not output before removing or installing the HV battery. If this DTC is output, perform troubleshooting for this DTC first.

  3. REMOVE SERVICE PLUG GRIP

    Click here

  4. REMOVE DECK BOARD SUB-ASSEMBLY (w/ Deck Board)

    for Wagon:

    Click here

  5. REMOVE DECK BOARD ASSEMBLY (w/ Deck Board)



  6. REMOVE FRONT DECK FLOOR BOX (w/ Deck Board)


  7. REMOVE REAR FLOOR MAT ASSEMBLY



  8. REMOVE REAR DECK FLOOR BOX (w/ Deck Floor Box)


  9. REMOVE DECK FLOOR BOX LH (w/ Deck Floor Box)


  10. REMOVE REAR SEAT CUSHION ASSEMBLY



  11. REMOVE REAR SEAT HEADREST ASSEMBLY

  12. DISCONNECT REAR NO. 1 SEAT LOCK CABLE ASSEMBLY (for LH Side)


  13. REMOVE REAR SEATBACK ASSEMBLY LH



  14. REMOVE REAR UNDER SIDE COVER LH



  15. REMOVE REAR UNDER SIDE COVER RH



  16. REMOVE REAR UNDER COVER

    Click here

  17. REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

    Click here

  18. REMOVE INVERTER COVER

    Click here

  19. CHECK TERMINAL VOLTAGE

    Click here

  20. INSTALL INVERTER COVER

    Click here

  21. REMOVE REAR DOOR SCUFF PLATE LH



  22. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH



  23. REMOVE REAR SEATBACK HINGE SUB-ASSEMBLY LH



  24. REMOVE REAR SEAT SIDE GARNISH LH



  25. REMOVE BATTERY COOLING BLOWER ASSEMBLY

    Click here

  26. REMOVE HYBRID BATTERY COVER SUB-ASSEMBLY RH

    CAUTION:

    Wear insulated gloves.


    1. A01KR6KC01
      *1 Service Plug Grip
      *2 Battery Cover Lock Striker
      *a Projection
      *b Turn
      *c Button

      Using the service plug grip, remove the battery cover lock striker.

      Tech Tips

      Insert the projection of the service plug grip, turn the button of the battery cover lock striker counterclockwise, and release the lock.

    2. A01KRO0

      Remove the 3 nuts and hybrid battery cover sub-assembly RH.

  27. DISCONNECT FRAME WIRE

    CAUTION:

    Wear insulated gloves.

    Note

    Insulate the disconnected connectors with insulating tape.


    1. A01KSJ7C01
      *a Shielded Wire Ground

      Disconnect the 2 frame wire connectors from the hybrid battery junction block assembly.

    2. Disconnect the shielded wire ground and frame wire.

  28. DISCONNECT WIRE HARNESS


    1. A01KT60C01
      *a Hybrid Battery Junction Block Assembly Connector
      *b EV Battery Plug Connector

      Disconnect the hybrid battery junction block assembly connector, EV battery plug connector and 3 clamps.

    2. A01KRZP

      Disconnect the battery voltage sensor connector and 2 clamps.

  29. REMOVE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY

    Click here

  30. REMOVE NO. 2 HYBRID BATTERY INTAKE DUCT


    1. A01KS4F

      Disconnect the clamp from the No. 2 hybrid battery intake duct.

    2. Disconnect the HV battery thermistor from the No. 2 hybrid battery intake duct.

    3. Remove the clip and No. 2 hybrid battery intake duct from the HV battery.

  31. REMOVE NO. 1 HYBRID BATTERY EXHAUST DUCT


    1. A01KTR9C01
      *1 Service Plug Grip
      *2 Battery Cover Lock Striker
      *a Projection
      *b Turn
      *c Button

      Using the service plug grip, remove the battery cover lock striker.

      Tech Tips

      Insert the projection of the service plug grip, turn the button of the battery cover lock striker counterclockwise, and release the lock.

    2. A01KTD0

      Remove the No. 1 hybrid battery exhaust duct from the HV battery.

  32. REMOVE NO. 2 HYBRID BATTERY EXHAUST DUCT


    1. A01KRHO

      Disengage the 2 claws and remove the No. 2 hybrid battery exhaust duct from the No. 1 hybrid battery exhaust duct.

  33. REMOVE HV BATTERY

    CAUTION:

    Wear insulated gloves.


    1. A01KSJ8

      Remove the 6 bolts and HV battery.

      Note


      • Since the HV battery is very heavy, 2 people are needed to remove the HV battery. When removing the HV battery, do not damage the parts around it.

      • When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

      • To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

      • Use cardboard or other similar material to protect the HV battery and vehicle body from damage.

      • While lowering the HV battery from the vehicle, do not allow it to contact the vehicle.

      • When moving the hybrid battery assembly, make sure to use an engine lifter.

      Tech Tips

      Attach tape to the feet and edges of the HV battery to protect tools and the vehicle body.

  34. REMOVE NO. 1 HYBRID VEHICLE BATTERY COVER PANEL LH

    CAUTION:

    Wear insulated gloves.


    1. A01KRQJ

      Disconnect the battery voltage sensor connector and 2 clamps.

    2. A01KRXC

      Remove the 2 bolts, 3 nuts and No. 1 hybrid vehicle battery cover panel LH.

  35. REMOVE BATTERY VOLTAGE SENSOR

    Click here

  36. REMOVE NO. 2 HYBRID VEHICLE BATTERY SHIELD PANEL

    CAUTION:

    Wear insulated gloves.


    1. A01KR5S

      Remove the 2 bolts, nut and No. 2 hybrid vehicle battery shield panel.

  37. REMOVE UPPER HYBRID BATTERY COVER SUB-ASSEMBLY

    CAUTION:

    Be sure to wear insulated gloves and protective goggles.


    1. A01KT59

      Remove the 6 bolts, 3 nuts and upper hybrid battery cover sub-assembly.

  38. REMOVE NO. 2 HYBRID BATTERY SHIELD SUB-ASSEMBLY

    CAUTION:

    Be sure to wear insulated gloves and protective goggles.


    1. A01KSKU

      Disconnect the 2 clamps from the No. 2 hybrid battery shield sub-assembly.

    2. A01KRCK

      Remove the bolt and EV battery plug from the No. 2 hybrid battery shield sub-assembly as shown in the illustration.

    3. A01KTPN

      Remove the 2 nuts and No. 2 hybrid battery shield sub-assembly from the HV battery.

  39. REMOVE HYBRID BATTERY JUNCTION BLOCK ASSEMBLY

    Click here

  40. REMOVE NO. 3 HV BATTERY CARRIER BRACKET SUB-ASSEMBLY

    CAUTION:

    Be sure to wear insulated gloves and protective goggles.


    1. A01KSP5

      Remove the 6 nuts and No. 3 HV battery carrier bracket sub-assembly from the No. 1 hybrid vehicle battery shield panel.

  41. REMOVE NO. 1 HYBRID VEHICLE BATTERY SHIELD PANEL

    CAUTION:

    Be sure to wear insulated gloves and protective goggles.


    1. A01KSEG

      Remove the 2 bolts and No. 1 hybrid vehicle battery shield panel from the HV battery.