HYBRID CONTROL SYSTEM Pattern Select Switch Eco Mode Circuit

DESCRIPTION

When selecting ECO mode, the ECO mode switch (combination switch assembly) operation signal is sent to the air conditioning amplifier assembly. Following this, ECO mode control is activated for the heater and air conditioning system.

WIRING DIAGRAM

PROCEDURE

1. READ VALUE USING GTS (CAN BUS CHECK)

   Result
   Proceed to A B

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the power switch on (IG).

   3. Enter the following menus: System Select / CAN Bus Check.

      Result
      Result Proceed to All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. A None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed. B

   4. Turn the power switch off.

   
   

   B

   GO TO CAN COMMUNICATION SYSTEM Click here

   A

2. CHECK DTC OUTPUT (HEALTH CHECK)

   Result
   Proceed to A B

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the power switch on (IG).

   3. Enter the following menus: System Select / Health Check.

   4. Check for DTCs.

      Result
      Result Proceed to No DTCs are output. A DTCs are output. B

   5. Turn the power switch off.

   
   

   B

   GO TO DTC CHART

   A

3. PERFORM ACTIVE TEST USING GTS (INDICAT. ECO MODE)

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the power switch on (IG).

   3. Enter the following menus: Body Electrical / Combination Meter / Active Test / Indicat. ECO MODE.

      
      Body Electrical > Combination Meter > Active Test

      Tester Display
      Indicat. ECO MODE

   4. Perform the "Indicat. ECO Mode" Active Test.

      OK
      The ECO mode indicator light comes on or blinks.

   5. Turn the power switch off.

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE COMBINATION METER ASSEMBLY Click here

   OK

4. READ VALUE USING GTS (ECO MODE)

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the power switch on (IG).

   3. Enter the following menus: Powertrain / Hybrid Control / Data List / ECO Mode.

      
      Powertrain > Hybrid Control > Data List

      Tester Display
      ECO Mode

   4. Read the value displayed on the GTS.

      
      Powertrain > Hybrid Control > Data List

      Tester Display	Measurement Item	Range	Normal Condition
      ECO Mode	ECO mode transition availability	ON or OFF	In ECO mode: ON

      Result
      Result Proceed to The GTS display changes according to the ECO mode switch (combination switch assembly) operation. A The GTS display does not change according to the ECO mode switch (combination switch assembly) operation. B

   
   

   A

   CHECK FOR INTERMITTENT PROBLEMS Click here

   B

5. READ VALUE USING GTS (ECO SWITCH)

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the power switch on (IG).

   3. Enter the following menus: Body Electrical / Air Conditioning / Data List / ECO Switch.

      
      Body Electrical > Air Conditioner > Data List

      Tester Display
      ECO Switch

   4. Read the value displayed on the GTS.

      
      Body Electrical > Air Conditioner > Data List

      Tester Display	Measurement Item	Range	Normal Condition
      ECO Switch	ECO mode switch (combination switch assembly) condition	ON or OFF	ECO mode switch (combination switch assembly) being pushed and held at ECO position: ON Mode switch not turned: OFF

      Result
      Result Proceed to The GTS display changes according to the ECO mode switch (combination switch assembly) operation. A The GTS display does not change according to the ECO mode switch (combination switch assembly) operation. B

   
   

   A

   REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

   B

6. INSPECT ECO MODE SWITCH (COMBINATION SWITCH ASSEMBLY)

   
   

   1. Remove the ECO mode switch (combination switch assembly).

      Click here

   2. 

      *a	Component without harness connected (ECO Mode Switch (Combination Switch Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 2 (ECU) - 3 (E) ECO mode switch (combination switch assembly) being pushed and held Below 1 Ω ECO mode switch (combination switch assembly) not pushed 10 kΩ or higher

   3. Install the ECO mode switch (combination switch assembly).

      Result
      Proceed to OK NG

   
   

   NG

   REPLACE ECO MODE SWITCH (COMBINATION SWITCH ASSEMBLY) Click here

   OK

7. CHECK HARNESS AND CONNECTOR (ECO MODE SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND)

   
   

   1. Disconnect the E114 ECO mode switch (combination switch assembly) connector.

   2. 

      *a	Front view of wire harness connector (to ECO Mode Switch (Combination Switch Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition E114-3 (E) - Body ground Always Below 1 Ω

   3. Reconnect the E114 ECO mode switch (combination switch assembly) connector.

      Result
      Proceed to OK NG

   
   

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR

   OK

8. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - ECO MODE SWITCH (COMBINATION SWITCH ASSEMBLY))

   
   

   1. Disconnect the E28 air conditioning amplifier assembly connector.

   2. Disconnect the E114 ECO mode switch (combination switch assembly) connector.

   3. 

      *a	Front view of wire harness connector (to Air Conditioning Amplifier Assembly)
      *b	Front view of wire harness connector (to ECO Mode Switch (Combination Switch Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition E28-24 (ECOS) - E114-2 (ECU) Always Below 1 Ω E28-24 (ECOS) or E114-2 (ECU) - Body ground Always 10 kΩ or higher

   4. Reconnect the E114 ECO mode switch (combination switch assembly) connector.

   5. Reconnect the E28 air conditioning amplifier assembly connector.

      Result
      Proceed to OK NG

   
   

   OK

   REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY Click here

   NG

   REPAIR OR REPLACE HARNESS OR CONNECTOR