HYBRID CONTROL SYSTEM, Diagnostic DTC:P0D2E-586

DESCRIPTION

For a description of the inverter.

Click here

The signal line from the inverter voltage (VH) sensor is connected to the MG ECU inside the inverter with converter assembly.

PROCEDURE

1. CHECK DTC OUTPUT (HYBRID CONTROL)

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the power switch on (IG).

   3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

   4. Check for DTCs.

      
      Powertrain > Hybrid Control > Trouble Codes

      Result
      Result Proceed to P0D2E-586 only is output, or DTCs except the ones in the tables below are also output. A DTCs shown in Table 1 are output simultaneously. B DTCs shown in Table 2 are output simultaneously. C
      Table 1 DTC No. Relevant Diagnosis P06E6-164 Sensor Power Supply "C" Circuit / Open P0A1A-151, 658 Generator Control Module P0A1B-786 Drive Motor "A" Control Module P0A1D-148 Hybrid Powertrain Control Module P0D2F-266 Drive Motor "A" Inverter Voltage Sensor Circuit Low P0D30-267 Drive Motor "A" Inverter Voltage Sensor Circuit High P0E33-589 DC/DC Converter Voltage Sensor "A" Low P0E34-590 DC/DC Converter Voltage Sensor "A" High P1C2A-155 Generator A/D Converter Circuit P1C73-512 Sensor Standard Voltage "F" Circuit / Open P1CA6-156 Generator Control Module Malfunction P1CA7-193 Drive Motor Control Module Malfunction P2511-149 HV CPU Power Relay Sense Circuit Intermittent No Continuity P3133-659 Communication Error from Generator to Drive Motor "A" P3134-661 Communication Error from Drive Motor "A" to Generator P324E-788 MG-ECU Power Relay Intermittent Circuit U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"
      Table 2 DTC No. Relevant Diagnosis P0AFC-123 Hybrid Battery Pack Sensor Module P0B3D-123 Hybrid Battery Voltage Sensor "A" Circuit Low P0B42-123 Hybrid Battery Voltage Sensor "B" Circuit Low P0B47-123 Hybrid Battery Voltage Sensor "C" Circuit Low P0B4C-123 Hybrid Battery Voltage Sensor "D" Circuit Low P0B51-123 Hybrid Battery Voltage Sensor "E" Circuit Low P0B56-123 Hybrid Battery Voltage Sensor "F" Circuit Low P0B5B-123 Hybrid Battery Voltage Sensor "G" Circuit Low P0B60-123 Hybrid Battery Voltage Sensor "H" Circuit Low P0B65-123 Hybrid Battery Voltage Sensor "I" Circuit Low P0B6A-123 Hybrid Battery Voltage Sensor "J" Circuit Low P0B6F-123 Hybrid Battery Voltage Sensor "K" Circuit Low P0B74-123 Hybrid Battery Voltage Sensor "L" Circuit Low P0B79-123 Hybrid Battery Voltage Sensor "M" Circuit Low P0B7E-123 Hybrid Battery Voltage Sensor "N" Circuit Low P0B83-123 Hybrid Battery Voltage Sensor "O" Circuit Low P308A-123 Hybrid Battery Voltage Sensor All Circuits Low

      Note

      
      

      • *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

      • P0D2E-586 may be stored due to a malfunction which causes the DTCs in the preceding tables to be stored. In this case, first troubleshoot the output DTCs in the preceding tables. Then, perform a reproduction test to check that no DTCs are output.

   5. Turn the power switch off.

   
   

   A

   REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS Click here

   B

   GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here

   C

   GO TO DTC CHART (HYBRID BATTERY SYSTEM) Click here