HYBRID CONTROL SYSTEM, Diagnostic DTC:P3108-536

DTC Code DTC Name
P3108-536 Lost Communication with A/C System Control Module

DESCRIPTION

The power management control ECU detects a wiring malfunction in the serial communication line between it and the compressor with motor assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P3108-536 Lost Communication with A/C System Control Module A/C inverter malfunction

  • Wire harness or connector

  • Compressor with motor assembly

  • Power management control ECU

 Does not come on

Master Warning Light:

Does not come on

WIRING DIAGRAM

A01SFADE02
*a Compressor with Motor Assembly
*b Power Management Control ECU

PROCEDURE


  1. CHECK DTC OUTPUT (AIR CONDITIONING SYSTEM)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.

    4. Check for DTCs.


      Body Electrical > Air Conditioner > Trouble Codes
      Result
      Result Proceed to
      DTCs related to A/C are not output. A
      DTCs related to A/C are output. B

    5. Turn the power switch off.


    B

    GO TO DTC CHART (AIR CONDITIONING SYSTEM) Click here

    A

  2. CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

    Result
    Proceed to
    OK
    NG

    1. Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors.

      Click here

      OK
      The connectors are connected securely and there are no contact pressure problems.
      A013A39C01
      *1 for LHD *2 for RHD
      Result
      Proceed to
      OK
      NG

    NG

    CONNECT SECURELY

    OK

  3. CHECK CONNECTOR CONNECTION CONDITION (COMPRESSOR WITH MOTOR ASSEMBLY CONNECTOR)


    1. A01SFFDN02

      Check the connection of the B170 compressor with motor assembly connector.

      OK
      The connector is connected securely and there are no contact problems.
      Result
      Proceed to
      OK
      NG

    NG

    CONNECT SECURELY

    OK

  4. CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)


    1. Disconnect the B170 compressor with motor assembly connector.

    2. A01SFHPC12
      *a

      Front view of wire harness connector

      (to Compressor with Motor Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B170-5 (GND) - Body ground Power switch off Below 1 Ω

    3. Turn the power switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      B170-6 (IG1) - B170-5 (GND) Power switch on (IG) 11 to 14 V

      Note

      Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    5. Turn the power switch off.

    6. Reconnect the B170 compressor with motor assembly connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)


    1. Disconnect the A129 power management control ECU connector.

    2. Disconnect the B170 compressor with motor assembly connector.

    3. Turn the power switch on (IG).

    4. A01SFN7C32
      *a

      Rear view of wire harness connector

      (to Power Management Control ECU)
      *b

      Front view of wire harness connector

      (to Compressor with Motor Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A129-19 (CLK) - Body ground Power switch on (IG) Below 1 V
      A129-20 (STB) - Body ground Power switch on (IG) Below 1 V
      A129-30 (ETI) - Body ground Power switch on (IG) Below 1 V
      A129-31 (ITE) - Body ground Power switch on (IG) Below 1 V

      Note

      Turning the power switch on (IG) with the power management control ECU connector and the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    5. Turn the power switch off.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      A129-19 (CLK) - B170-1 (CLK) Power switch off Below 1 Ω
      A129-20 (STB) - B170-4 (STBI) Power switch off Below 1 Ω
      A129-30 (ETI) - B170-3 (DOUT) Power switch off Below 1 Ω
      A129-31 (ITE) - B170-2 (DIN) Power switch off Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      A129-19 (CLK) or B170-1 (CLK) - Body ground and other terminals Power switch off 10 kΩ or higher
      A129-20 (STB) or B170-4 (STBI) - Body ground and other terminals Power switch off 10 kΩ or higher
      A129-30 (ETI) or B170-3 (DOUT) - Body ground and other terminals Power switch off 10 kΩ or higher
      A129-31 (ITE) or B170-2 (DIN) - Body ground and other terminals Power switch off 10 kΩ or higher

    7. Reconnect the B170 compressor with motor assembly connector.

    8. Reconnect the A129 power management control ECU connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK POWER MANAGEMENT CONTROL ECU


    1. Disconnect the B170 compressor with motor assembly connector.

    2. A01SFHPC17
      *a

      Front view of wire harness connector

      (to Compressor with Motor Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B170-3 (DOUT) - Body ground Power switch off 10 kΩ or higher
      B170-4 (STBI) - Body ground Power switch off 10 kΩ or higher

    3. Turn the power switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      B170-1 (CLK) - Body ground Power switch on (IG) 11 to 14 V
      B170-2 (DIN) - Body ground Power switch on (IG) 11 to 14 V
      B170-3 (DOUT) - Body ground Power switch on (IG) Below 1 V
      B170-4 (STBI) - Body ground Power switch on (IG) Below 1 V

      Note

      Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    5. Turn the power switch off.

    6. Reconnect the B170 compressor with motor assembly connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE POWER MANAGEMENT CONTROL ECU for LHD: Click here
    REPLACE POWER MANAGEMENT CONTROL ECU for RHD: Click here

    OK

  7. CHECK COMPRESSOR WITH MOTOR ASSEMBLY


    1. Disconnect the A129 power management control ECU connector.

    2. A01SFFRC01
      *a

      Rear view of wire harness connector

      (to Power Management Control ECU)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A129-19 (CLK) - Body ground Power switch off 10 kΩ or higher
      A129-31 (ITE) - Body ground Power switch off 10 kΩ or higher

    3. Turn the power switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A129-19 (CLK) - Body ground Power switch on (IG) Below 1 V
      A129-20 (STB) - Body ground Power switch on (IG) Below 1 V
      A129-30 (ETI) - Body ground Power switch on (IG) 11 to 14 V
      A129-31 (ITE) - Body ground Power switch on (IG) Below 1 V

      Note

      Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    5. Turn the power switch off.

    6. Reconnect the A129 power management control ECU connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POWER MANAGEMENT CONTROL ECU for LHD: Click here
    REPLACE POWER MANAGEMENT CONTROL ECU for RHD: Click here

    NG

    REPLACE COMPRESSOR WITH MOTOR ASSEMBLY Click here