HYBRID CONTROL SYSTEM, Diagnostic DTC:P3000-389

DTC Code DTC Name
P3000-389 Battery Control System

DESCRIPTION

The power management control ECU alerts the driver and performs fail-safe control based on error signals received from the battery voltage sensor.

This DTC is stored if the HV battery is discharged excessively or the hybrid control system malfunctions.

Tech Tips

If the HV battery voltage has dropped due to a malfunction in other components such as the inverter with converter assembly or the hybrid vehicle transaxle assembly, recharging the HV battery will restore the voltage. If the HV battery voltage has dropped excessively after the vehicle was left for a long time, the HV battery will need to be replaced.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P3000-389 Battery Control System HV battery voltage drops

  • Engine

  • Hybrid vehicle transaxle assembly

  • HV battery

 Does not come on

Master Warning Light:

Comes on

CAUTION / NOTICE / HINT

CAUTION:

When disposing of an HV battery, make sure to return it through an authorized collection agent who is capable of handling it safely. If the HV battery is returned via the manufacturer specified route, it will be returned properly and in a safe manner by an authorized collection agent.

Tech Tips


  • If the vehicle is stopped or parked with neutral (N) selected for a long time, DTC P3000-389 may be stored because the HV battery cannot be charged.

  • When the engine cannot be started, DTC P3000-389 may be stored because the HV battery cannot be charged.

PROCEDURE


  1. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check for DTCs.


      Powertrain > Hybrid Control > Trouble Codes
      Result
      Result Proceed to
      P3000-389 or P3000-388 only is output. A
      DTCs other than P3000-389 and P3000-388 are also output. B

      Tech Tips

      If the HV battery voltage has dropped due to a malfunction in other components such as the inverter with converter assembly or the hybrid vehicle transaxle assembly, recharge the HV battery and then repair the malfunctioning part.

    5. Turn the power switch off.


    B

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here

    A

  2. CHECK DTC OUTPUT (ENGINE AND ECT)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    4. Check for DTCs.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Result Proceed to
      No DTCs are output. A
      DTCs are output. B

    5. Turn the power switch off.


    B

    GO TO DTC CHART (SFI SYSTEM) Click here

    A

  3. CHECK ENGINE START


    1. Turn the power switch on (READY).

    2. Check if the engine starts.

      Note

      Do not turn the power switch on (READY) repeatedly after duplicating the problem symptom indicated by DTC P3000-389 and clearing the DTCs. This may cause another problem to occur.

      Tech Tips

      Depressing the accelerator pedal with park (P) selected will cause the engine to start.

      Result
      Result Proceed to
      The engine does not start. A
      The engine starts. B

    3. Turn the power switch off.


    B

    LEAVE VEHICLE WITH PARK (P) SELECTED, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS

    A

  4. CHECK CRANKSHAFT PULLEY REVOLUTION (P POSITION)


    1. Make sure that park (P) is selected.

    2. Lift up the vehicle.

    3. Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

      CAUTION:

      Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch off before performing this inspection, to prevent the engine from starting.

      Note

      Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.

      Result
      Result Proceed to
      The crankshaft rotates smoothly. A
      The crankshaft does not rotate smoothly. B

    4. Lower the vehicle.


    B

    CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION) Click here

    A

  5. CHECK HV BATTERY


    1. Turn the power switch off.

    2. Wait 10 minutes or more.

    3. Connect the GTS to the DLC3.

    4. Turn the power switch on (IG).

    5. Enter the following menus: Powertrain / Hybrid Control / Data List / Battery Block Vol - V01 to 14.


      Powertrain > Hybrid Control > Data List
      Tester Display
      Battery Block Vol -V01
      Battery Block Vol -V02
      Battery Block Vol -V03
      Battery Block Vol -V04
      Battery Block Vol -V05
      Battery Block Vol -V06
      Battery Block Vol -V07
      Battery Block Vol -V08
      Battery Block Vol -V09
      Battery Block Vol -V10
      Battery Block Vol -V11
      Battery Block Vol -V12
      Battery Block Vol -V13
      Battery Block Vol -V14

    6. Read the Data List.

      Result
      Result Proceed to
      One or more battery block voltages are below 12.0 V. A
      All battery block voltages are 12.0 V or more. B

    7. Turn the power switch off.


    A

    REPLACE HV BATTERY Click here

    B

    CHARGE HV BATTERY (ABOUT 10 MINUTES) Click here

  6. CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)


    1. Turn the power switch on (IG).

    2. Move the shift lever to N.

    3. Lift up the vehicle.

    4. Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

      CAUTION:

      Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch on (IG) before performing this inspection, to prevent the engine from starting.

      Note

      Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.

      Result
      Result Proceed to
      The crankshaft does not rotate smoothly. A
      The crankshaft rotates smoothly. B

    5. Lower the vehicle.


    B

    REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY Click here

    A

  7. REPAIR OR REPLACE ENGINE

    Result
    Proceed to
    NEXT

    NEXT

  8. CHECK ENGINE START


    1. Turn the power switch on (READY).

    2. Check if the engine starts.

      Note

      Do not turn the power switch on (READY) repeatedly after duplicating the problem symptom indicated by DTC P3000-389 and clearing the DTCs. This may cause another problem to occur.

      Tech Tips

      Depressing the accelerator pedal with park (P) selected will cause the engine to start.

      Result
      Result Proceed to
      The engine does not start. A
      The engine starts. B

    3. Turn the power switch off.


    B

    LEAVE VEHICLE WITH PARK (P) SELECTED, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS

    A

  9. CHECK HV BATTERY


    1. Turn the power switch off.

    2. Wait 10 minutes or more.

    3. Turn the power switch on (IG).

    4. Enter the following menus: Powertrain / Hybrid Control / Data List / Battery Block Vol - V01 to 14.


      Powertrain > Hybrid Control > Data List
      Tester Display
      Battery Block Vol -V01
      Battery Block Vol -V02
      Battery Block Vol -V03
      Battery Block Vol -V04
      Battery Block Vol -V05
      Battery Block Vol -V06
      Battery Block Vol -V07
      Battery Block Vol -V08
      Battery Block Vol -V09
      Battery Block Vol -V10
      Battery Block Vol -V11
      Battery Block Vol -V12
      Battery Block Vol -V13
      Battery Block Vol -V14

    5. Read the Data List.

      Result
      Result Proceed to
      One or more battery block voltage is below 12.0 V. A
      All battery block voltages are 12.0 V or more. B

    6. Turn the power switch off.


    A

    REPLACE HV BATTERY Click here

    B

    CHARGE HV BATTERY (ABOUT 10 MINUTES) Click here

  10. REPLACE HYBRID VEHICLE TRANSAXLE ASSEMBLY

    Click here

    Result
    Proceed to
    NEXT

    NEXT

  11. CHECK ENGINE START


    1. Turn the power switch on (READY).

    2. Check if the engine starts.

      Note

      Do not turn the power switch on (READY) repeatedly after duplicating the problem symptom indicated by DTC P3000-389 and clearing the DTCs. This may cause another problem to occur.

      Tech Tips

      Depressing the accelerator pedal with park (P) selected will cause the engine to start.

      Result
      Result Proceed to
      The engine does not start. A
      The engine starts. B

    3. Turn the power switch off.


    B

    LEAVE VEHICLE WITH PARK (P) SELECTED, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS

    A

  12. CHECK HV BATTERY


    1. Turn the power switch off.

    2. Wait 10 minutes or more.

    3. Turn the power switch on (IG).

    4. Enter the following menus: Powertrain / Hybrid Control / Data List / Battery Block Vol - V01 to 14.


      Powertrain > Hybrid Control > Data List
      Tester Display
      Battery Block Vol -V01
      Battery Block Vol -V02
      Battery Block Vol -V03
      Battery Block Vol -V04
      Battery Block Vol -V05
      Battery Block Vol -V06
      Battery Block Vol -V07
      Battery Block Vol -V08
      Battery Block Vol -V09
      Battery Block Vol -V10
      Battery Block Vol -V11
      Battery Block Vol -V12
      Battery Block Vol -V13
      Battery Block Vol -V14

    5. Read the Data List.

      Result
      Result Proceed to
      One or more battery block voltage is below 12.0 V. A
      All battery block voltages are 12.0 V or more. B

    6. Turn the power switch off.


    A

    REPLACE HV BATTERY Click here

    B

    CHARGE HV BATTERY (ABOUT 10 MINUTES) Click here