HYBRID CONTROL SYSTEM, Diagnostic DTC:P0ADF-229

DTC Code DTC Name
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low

DESCRIPTION

Refer to the description for DTC P0AE6-225.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0ADF-229 Hybrid Battery Negative Contactor Control Circuit Low Short to GND in the SMRG circuit

  • Wire harness or connector

  • Hybrid battery junction block assembly

  • Hybrid vehicle control ECU assembly

 Does not come on

Master Warning Light:

Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0AE6-225.

Click here

CAUTION / NOTICE / HINT

CAUTION:


  • Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    Click here

    Tech Tips

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

Tech Tips

If P0ADF-229 is stored, the hybrid system cannot be started.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - BODY GROUND)


    1. Disconnect the E135 hybrid vehicle control ECU assembly connector.

    2. A01KREJC22
      *a

      Rear view of wire harness connector

      (to Hybrid Vehicle Control ECU Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E135-1 (SMRG) - Body ground Power switch off 25.0 to 59.0 Ω

    3. Reconnect the E135 hybrid vehicle control ECU assembly connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY for LHD: Click here
    REPLACE HYBRID VEHICLE CONTROL ECU ASSEMBLY for RHD: Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU ASSEMBLY - HYBRID BATTERY JUNCTION BLOCK ASSEMBLY)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Disconnect the L49 hybrid battery junction block assembly connector.

    3. Disconnect the E135 hybrid vehicle control ECU assembly connector.

    4. A01KRCSC91
      *a

      Rear view of wire harness connector

      (to Hybrid Vehicle Control ECU Assembly)
      *b

      Rear view of wire harness connector

      (to Hybrid Battery Junction Block Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E135-1 (SMRG) or L49-3 (SMRG) - Body ground and other terminals Power switch off 10 kΩ or higher

    5. Reconnect the E135 hybrid vehicle control ECU assembly connector.

    6. Reconnect the L49 hybrid battery junction block assembly connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE HV BATTERY JUNCTION BLOCK ASSEMBLY Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR