HYBRID CONTROL SYSTEM, Diagnostic DTC:P0AFC-129

DTC Code DTC Name
P0AFC-129 Hybrid Battery Pack Sensor Module

DESCRIPTION

The battery voltage sensor (battery energy control module) sends HV battery voltage information to the power management control ECU via serial communication.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0AFC-129 Hybrid Battery Pack Sensor Module HV battery voltage circuit malfunction Battery voltage sensor Comes on

Master Warning Light:

Comes on

CAUTION / NOTICE / HINT

Note

Performing the check procedures for a long time with the shift lever in N may cause DTC P3000-388 to be set.

Tech Tips

If it is necessary to replace the battery voltage sensor, voltages need to be confirmed after installing the new battery voltage sensor. Confirm that "Power Resource VB", "VL-Voltage before Boosting", and "VH-Voltage after Boosting" in the Data List are 220 V or more with the power switch on (READY), the shift lever in P, and the engine stopped. When the system is normal, the "Power Resource VB", "VL-Voltage before Boosting", and "VH-Voltage after Boosting" values should be almost equal (voltage boosting will not occur when the shift lever is in N). If the difference between each voltage exceeds the values specified below, there is a malfunction in the inverter with converter assembly.

Inspection voltage Maximum voltage difference
Difference between "Power Resource VB" and "VL-Voltage before Boosting" 50 V
Difference between "Power Resource VB" and "VH-Voltage after Boosting" 70 V
Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" 90 V

PROCEDURE


  1. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check for DTCs.


      Powertrain > Hybrid Control > Trouble Codes
      Result
      Result Proceed to
      P0AFC-129 only is output, or DTCs except the ones in the tables below are also output. A
      DTCs shown in Table 1 are output simultaneously. B
      DTCs shown in Table 2 are output simultaneously. C
      Table 1
      DTC No. Relevant Diagnosis
      P0A1A-151, 155, 156, 658, 659 Generator Control Module
      P0A1B-164, 193, 512, 661, 786 Drive Motor "A" Control Module
      P0A1D-148 Hybrid Powertrain Control Module
      P0A78-266, 267 Drive Motor "A" Inverter Performance
      P0A94-589, 590 DC / DC Converter Performance
      P2511-149 ECM/PCM Power Relay Sensor Circuit Intermittent
      P3004-132 High Voltage Power Resource
      P324E-788 MG-ECU Power Relay Intermittent Circuit
      U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"
      Table 2
      DTC No. Relevant Diagnosis
      P0AFC-123 Hybrid Battery Pack Sensor Module
      P0B3D-123 Hybrid Battery Voltage Sensor "A" Circuit Low
      P0B42-123 Hybrid Battery Voltage Sensor "B" Circuit Low
      P0B47-123 Hybrid Battery Voltage Sensor "C" Circuit Low
      P0B4C-123 Hybrid Battery Voltage Sensor "D" Circuit Low
      P0B51-123 Hybrid Battery Voltage Sensor "E" Circuit Low
      P0B56-123 Hybrid Battery Voltage Sensor "F" Circuit Low
      P0B5B-123 Hybrid Battery Voltage Sensor "G" Circuit Low
      P0B60-123 Hybrid Battery Voltage Sensor "H" Circuit Low
      P0B65-123 Hybrid Battery Voltage Sensor "I" Circuit Low
      P0B6A-123 Hybrid Battery Voltage Sensor "J" Circuit Low
      P0B6F-123 Hybrid Battery Voltage Sensor "K" Circuit Low
      P0B74-123 Hybrid Battery Voltage Sensor "L" Circuit Low
      P0B79-123 Hybrid Battery Voltage Sensor "M" Circuit Low
      P0B7E-123 Hybrid Battery Voltage Sensor "N" Circuit Low
      P0B83-123 Hybrid Battery Voltage Sensor "O" Circuit Low
      P308A-123 Hybrid Battery Voltage Sensor All Circuits Low

      Note


      • *1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

      • P0AFC-129 may be stored due to a malfunction which causes the DTCs in the preceding tables to be stored. In this case, first troubleshoot the output DTCs in the preceding tables. Then, perform a reproduction test to check that no DTCs are output.

    5. Turn the power switch off.


    A

    REPLACE BATTERY VOLTAGE SENSOR Click here

    B

    GO TO DTC CHART (HYBRID CONTROL SYSTEM) Click here

    C

    GO TO DTC CHART (HYBRID BATTERY SYSTEM) Click here