HYBRID CONTROL SYSTEM, Diagnostic DTC:P06B0-163, P06D6-511, P06E6-164, P0A1A-151, P0A1A-166, P0A1A-658, P0A1A-791, P0A1B-198, P0A1B-786, P0A1B-794, P1C2A-155, P1C2B-192, P1C73-512, P1CA6-156, P1CA7-193, P3133-659, P3134-661

DTC Code DTC Name
P06B0-163 Sensor Power Supply "A" Circuit / Open
P06D6-511 Sensor Reference Voltage "F" Circuit / Open
P06E6-164 Sensor Power Supply "C" Circuit / Open
P0A1A-151 Generator Control Module
P0A1A-166 Generator Control Module
P0A1A-658 Generator Control Module
P0A1A-791 Generator Control Module
P0A1B-198 Drive Motor "A" Control Module
P0A1B-786 Drive Motor "A" Control Module
P0A1B-794 Drive Motor "A" Control Module
P1C2A-155 Generator A/D Converter Circuit
P1C2B-192 Drive Motor "A" A/D Converter Circuit
P1C73-512 Sensor Standard Voltage "F" Circuit / Open
P1CA6-156 Generator Control Module Malfunction
P1CA7-193 Drive Motor Control Module Malfunction
P3133-659 Communication Error from Generator to Drive Motor "A"
P3134-661 Communication Error from Drive Motor "A" to Generator

DESCRIPTION

The MG ECU located in the inverter with converter assembly monitors its internal operation and it will store DTCs when it detects malfunctions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P06B0-163 Sensor Power Supply "A" Circuit / Open IPM positive power source error Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P06D6-511 Sensor Reference Voltage "F" Circuit / Open Standard voltage for analog signal offset error Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P06E6-164 Sensor Power Supply "C" Circuit / Open IPM negative power source error Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P0A1A-151 Generator Control Module Run pulse signal cycle deviation or stop Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P0A1A-166 Generator Control Module R/D converter NM stop error Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P0A1A-658 Generator Control Module ALU error Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P0A1A-791 Generator Control Module R/D converter communication error Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P0A1B-198 Drive Motor "A" Control Module R/D converter NM stop error Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P0A1B-786 Drive Motor "A" Control Module ALU error Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P0A1B-794 Drive Motor "A" Control Module R/D converter communication error Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P1C2A-155 Generator A/D Converter Circuit A/D converter error Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P1C2B-192 Drive Motor "A" A/D Converter Circuit A/D converter error Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P1C73-512 Sensor Standard Voltage "F" Circuit / Open Standard voltage for analog signal error Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P1CA6-156 Generator Control Module Malfunction CPU ROM-RAM error Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P1CA7-193 Drive Motor Control Module Malfunction CPU ROM-RAM error Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P3133-659 Communication Error from Generator to Drive Motor "A" Communication error (from MG1 to MG2) Inverter with converter assembly Comes on

Master Warning Light:

Comes on
P3134-661 Communication Error from Drive Motor "A" to Generator Communication error (from MG2 to MG1) Inverter with converter assembly Comes on

Master Warning Light:

Comes on

PROCEDURE


  1. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    4. Check for DTCs.


      Powertrain > Hybrid Control > Trouble Codes
      Result
      Result Proceed to
      DTCs except those listed in the following table are output. A
      Any of the following DTCs are also output. B
      DTC No. Relevant Diagnosis
      P06B0-163 Sensor Power Supply "A" Circuit / Open
      P06D6-511 Sensor Reference Voltage "F" Circuit /Open
      P06E6-164 Sensor Power Supply "C" Circuit / Open
      P0A1A-166, 658, 791 Generator Control Module
      P0A1B-198, 786, 794 Drive Motor "A" Control Module
      P1C2A-155 Generator A/D Converter Circuit
      P1C2B-192 Drive Motor "A" A/D Converter Circuit
      P1C73-512 Sensor Standard Voltage "F" Circuit /Open
      P1CA6-156 Generator Control Module Malfunction
      P1CA7-193 Drive Motor Control Module Malfunction
      P3134-661 Communication Error from Drive Motor "A" to Generator

    5. Turn the power switch off.


    B

    REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS Click here

    A

  2. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    4. Check for DTCs.


      Powertrain > Hybrid Control > Trouble Codes
      Result
      Result Proceed to
      Only DTC P0A1A-151, P3133-659 or P324E-788 is output. A
      Other than above. B

    5. Turn the power switch off.


    B

    GO TO DTC CHART (HYBRID CONTROL) Click here

    A

  3. CLEAR DTC

    Result
    Proceed to
    NEXT

    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Read and record the DTCs and freeze frame data.


      Powertrain > Hybrid Control > Trouble Codes

    5. Clear the DTCs and freeze frame data.


      Powertrain > Hybrid Control > Clear DTCs

    6. Turn the power switch off.

      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch off and wait for 30 seconds or more.

    3. Turn the power switch on (IG) and wait for 5 seconds or more.

    4. Turn the power switch on (READY).

    5. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    6. Check for DTCs.


      Powertrain > Hybrid Control > Trouble Codes
      Result
      Result Proceed to
      No DTCs are output (not including history DTCs). A
      Only DTC P0A1A-151, P3133-659 or P324E-788 isoutput. B
      Other than above. C

    7. Turn the power switch off.


    A

    REPLACE MG CONTROL COMPUTER Click here

    B

    REPLACE POWER MODULE INTELLIGENT TRANSISTOR KIT AND MG CONTROL COMPUTER Click here

    C

    GO TO DTC CHART (HYBRID CONTROL) Click here