HYBRID CONTROL SYSTEM, Diagnostic DTC:P0A10-263

DTC Code DTC Name
P0A10-263 DC / DC Converter Status Circuit High Input

DESCRIPTION

Refer to the description for DTC P0A08-264.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P0A10-263 DC / DC Converter Status Circuit High Input Short to +B in the DC/DC converter NODD signal line

  • Wire harness or connector

  • Inverter with converter assembly

  • Power management control ECU

 Does not come on

Master Warning Light:

Comes on

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A08-264.

Click here

CAUTION / NOTICE / HINT

CAUTION:


  • Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

    Click here

    Tech Tips

    Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

PROCEDURE


  1. CHECK POWER MANAGEMENT CONTROL ECU (NODD)

    Result
    Proceed to
    OK
    NG

    1. Turn the power switch on (READY).

    2. A01SF73C01
      *a

      Component with harness connected

      (Power Management Control ECU)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A129-21 (NODD) - E111-6 (E1) Power switch on (READY) 5 to 7 V

    3. Turn the power switch off.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK POWER MANAGEMENT CONTROL ECU (NODD) Click here

    OK

  2. CLEAR DTC

    Result
    Proceed to
    NEXT

    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Clear the DTCs and freeze frame data.


      Powertrain > Hybrid Control > Clear DTCs

    5. Turn the power switch off.

      Result
      Proceed to
      NEXT

    NEXT

  3. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (READY).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check for DTCs.


      Powertrain > Hybrid Control > Trouble Codes
      Result
      Result Proceed to
      P0A10-263 is not output. A
      P0A10-263 is output again. B

    5. Turn the power switch off.


    B

    REPLACE POWER MANAGEMENT CONTROL ECU for LHD: Click here
    REPLACE POWER MANAGEMENT CONTROL ECU for RHD: Click here

    A

  4. CHECK FOR INTERMITTENT PROBLEMS

    Click here

    Result
    Proceed to
    OK
    NG

    OK

    REPLACE POWER MANAGEMENT CONTROL ECU for LHD: Click here
    REPLACE POWER MANAGEMENT CONTROL ECU for RHD: Click here

    NG

    REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

  5. CHECK POWER MANAGEMENT CONTROL ECU (NODD)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Disconnect the A143 inverter with converter assembly connector.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Turn the power switch on (IG).

    5. A01SF97C25
      *a

      Front view of wire harness connector

      (to Inverter with Converter Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A143-12 (NODD) - Body ground Power switch on (IG) Below 1 V

      Note

      Turning the power switch on (IG) with the inverter with converter assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    6. Turn the power switch off.

    7. Disconnect the cable from the negative (-) auxiliary battery terminal.

    8. Reconnect the A143 inverter with converter assembly connector.

      Result
      Proceed to
      OK
      NG

    OK

    REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS Click here

    NG

  6. CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - POWER MANAGEMENT CONTROL ECU)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Check that the service plug grip is not installed.

      Note

      After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.

    2. Disconnect the A143 inverter with converter assembly connector.

    3. Disconnect the A129 power management control ECU connector.

    4. Connect the cable to the negative (-) auxiliary battery terminal.

    5. Turn the power switch on (IG).

    6. A01SFA7C11
      *a

      Front view of wire harness connector

      (to Inverter with Converter Assembly)
      *b

      Rear view of wire harness connector

      (to Power Management Control ECU)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A143-12 (NODD) or A129-21 (NODD) - Body ground Power switch on (IG) Below 1 V

      Note

      Turning the power switch on (IG) with the inverter with converter assembly connector and the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

    9. Reconnect the A143 inverter with converter assembly connector.

    10. Reconnect the A129 power management control ECU connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE POWER MANAGEMENT CONTROL ECU for LHD: Click here
    REPLACE POWER MANAGEMENT CONTROL ECU for RHD: Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR