REAR AXLE CARRIER INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY


    1. A00YMVS

      Secure the rear axle carrier sub-assembly between aluminum plates in a vise.

      Note

      Do not overtighten the vise.

    2. Using a brass bar and a hammer, push out the bushing until it is positioned as shown in the illustration.

      Tech Tips

      Pushing out the bushing makes it easier to install the rear axle carrier sub-assembly.

    3. Using a jack and wooden block, keep the rear No. 2 suspension arm assembly level.

      CAUTION:

      Do not jack up the rear No. 2 suspension arm assembly too high as the vehicle may fall.

      Note


      • When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

      • Make sure to perform this operation with the vehicle kept as low as possible.

    4. A00YNHVC06
      *1 No. 2 Flexible Hose Bracket
      A00YN9X Bolt (A)
      A00YQ1Y Bolt (B)
      A00YPH9 Bolt (C)

      Temporarily install the rear axle carrier sub-assembly to the rear No. 2 suspension arm assembly with the bolt (C) and nut.

      Note


      • Insert the bolt with the threaded end facing the front of the vehicle.

      • Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

    5. Temporarily install the rear axle carrier sub-assembly and No. 2 flexible hose bracket to the rear upper control arm assembly with the bolt (B) and nut.

      Note


      • Insert the bolt with the threaded end facing the rear of the vehicle.

      • Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

    6. Install the rear axle carrier sub-assembly to the rear trailing arm assembly with the 2 bolts (A).

      Torque:
      200 N*m  { 2039 kgf*cm, 148 ft.*lbf }

    7. Fully tighten the bolt (B) and bolt (C).

      Torque:
      90 N*m  { 918 kgf*cm, 66 ft.*lbf }

      Note

      Because the nuts have their own stoppers, do not turn the nuts. Tighten the bolts with the nuts secured.

    8. Slowly lower the rear No. 2 suspension arm assembly.

  2. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY

    Click here

  3. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

    Click here

  4. INSPECT REAR AXLE HUB BEARING LOOSENESS

    Click here

  5. INSPECT REAR AXLE HUB RUNOUT

    Click here

  6. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)

    Click here

  7. CONNECT SKID CONTROL SENSOR WIRE

    Click here

  8. INSTALL REAR DISC

    Click here

  9. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

    Click here

  10. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

    Click here

  11. INSTALL PARKING BRAKE LEVER PROTECTOR

    Click here

  12. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL


    1. Connect the cable to the negative (-) auxiliary battery terminal.

      Click here

    2. Connect the reservoir level switch connector.

    3. Clear the DTCs.

      Click here

  13. ADJUST PARKING BRAKE

    Click here

  14. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

    Click here

  15. INSTALL REAR FLOOR SIDE MEMBER COVER LH (for LH Side)

    Click here

  16. INSTALL REAR FLOOR SIDE MEMBER COVER RH (for RH Side)

    Click here

  17. INSTALL REAR SUSPENSION ARM COVER

    Click here

  18. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  19. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

    Click here

  20. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Click here

  21. CHECK FOR SPEED SENSOR SIGNAL

    Click here