БЕССТУПЕНЧАТАЯ ТРАНСМИССИЯ В СБОРЕ (для моделей с 8NR-FTS) СНЯТИЕ

CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with continuously variable transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.

PROCEDURE


  1. REMOVE FLYWHEEL HOUSING UNDER COVER

    Click here

  2. REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT


    1. A0030FK

      Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

      Tech Tips

      There will be one black colored drive plate and torque converter assembly setting bolt.

  3. REMOVE FRONT SUSPENSION MEMBER REAR BRACE LH

    Click here

  4. REMOVE FRONT SUSPENSION MEMBER REAR BRACE RH

    Tech Tips

    Use the same procedure as for the LH side.

  5. REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

    Click here

  6. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

    Click here

  7. REMOVE FRONT ENGINE MOUNTING INSULATOR

    Click here

  8. REMOVE REAR ENGINE MOUNTING INSULATOR

    Click here

  9. REMOVE WIRE HARNESS CLAMP BRACKET

    Click here

  10. INSTALL ENGINE HANGER

    Click here

  11. REMOVE WATER HOSE

    Click here

  12. DISCONNECT ENGINE WIRE


    1. Disconnect the oil pump with motor assembly connector.

      A00317QC01
      *a Oil Pump with Motor Assembly Connector *b Transmission Revolution Sensor (NIN) Connector
      *c Transmission Wire Connector *d Park/Neutral Position Switch Assembly Connector
      *e Transmission Revolution Sensor (NOUT) Connector *f Oil Pressure Sensor Connector

    2. Disconnect the transmission revolution sensor (NIN) connector.

    3. Disconnect the transmission wire connector.

    4. Disconnect the park/neutral position switch assembly connector.

    5. Disconnect the transmission revolution sensor (NOUT) connector.

    6. Disconnect the oil pressure sensor connector.

    7. Disengage the 9 clamps.

  13. REMOVE FLYWHEEL HOUSING SIDE COVER

    Click here

  14. REMOVE STARTER ASSEMBLY

    Click here

  15. REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY


    1. Using a transmission jack attachment, set the continuously variable transaxle assembly on a transmission jack.

      Note


      • Secure the continuously variable transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.

      • To prevent the transaxle oil (CVT) pan sub-assembly from deforming, do not place any attachments under the transaxle oil (CVT) pan sub-assembly.

      • Hold the engine assembly with a suitable adapter, such as a rope, during the operation.

    2. A0030U1

      Remove the 7 bolts and continuously variable transaxle assembly from the engine assembly.

      Note

      To prevent damage to the 2 knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.

  16. REMOVE TORQUE CONVERTER ASSEMBLY


    1. A002ZLJ

      Remove the torque converter assembly from the continuously variable transaxle assembly.

      Note

      Remove the torque converter assembly from the input shaft horizontally.

  17. REMOVE CVT OIL PUMP TYPE T OIL SEAL

    CAUTION:


    • Do not remove the front oil pump assembly from the continuously variable transaxle assembly main body, as there is a possibility of the entry of dust and foreign matter.

    • Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a continuously variable transaxle assembly malfunction, which may prevent the vehicle from being driven, may occur if dust or fine foreign matter enters the continuously variable transaxle assembly.

    • Do not use cotton work gloves, cloths, paper towels, etc. that may produce lint, dust or foreign matter.

    • Perform the operation as quickly as possible, as dust and foreign matter may enter the continuously variable transaxle assembly while the torque converter assembly is not attached to it.

    • Do not use an air gun until the torque converter assembly has been installed, as it may cause dust and foreign matter to be stirred up.


    1. Clean the tips of both the claws of SST and center bolt.

      SST
      09308-10010
    2. A0030DSC02
      *1 CVT Oil Pump Type T Oil Seal
      *a Claw

      Using SST, remove the CVT oil pump type T oil seal from the continuously variable transaxle assembly.

      Note

      Pay attention to the angle of the claws of SST when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles may be produced if they do.

  18. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET


    1. A0030IT

      Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.

  19. REMOVE FRONT ENGINE MOUNTING BRACKET


    1. A0030VX

      Remove the 4 bolts and front engine mounting bracket from the continuously variable transaxle assembly.

  20. REMOVE REAR ENGINE MOUNTING BRACKET


    1. A00308S

      Remove the 3 bolts and rear engine mounting bracket from the continuously variable transaxle assembly.

  21. REMOVE ENGINE MOUNTING BRACKET LH


    1. A00302O

      Remove the 3 bolts and engine mounting bracket LH from the continuously variable transaxle assembly.

  22. REMOVE NO. 1 HEATER BRACKET SUB-ASSEMBLY


    1. A00306H

      Disconnect the No. 1 breather plug (CVT) from the clamp.

    2. A002ZMN

      Remove the clamp from the No. 1 heater bracket sub-assembly.

    3. A00318W

      Remove the bolt and No. 1 heater bracket sub-assembly from the continuously variable transaxle assembly.

  23. REMOVE WIRE HARNESS CLAMP BRACKET


    1. A0030OF

      Remove the 6 bolts and 6 wire harness clamp brackets from the continuously variable transaxle assembly.

  24. REMOVE WITH HEAD STRAIGHT SCREW PLUG

    Tech Tips

    Perform this procedure only when replacement of the with head straight screw plug is necessary.


    1. A0030HK

      Remove the with head straight screw plug and gasket from the continuously variable transaxle assembly.

  25. REMOVE NO. 1 BREATHER PLUG (CVT)

    Tech Tips

    Perform this procedure only when replacement of the No. 1 breather plug (CVT) is necessary.


    1. A0030XZ

      Remove the No. 1 breather plug (CVT) from the breather plug hose.

  26. INSPECT TORQUE CONVERTER ASSEMBLY

    Click here

  27. INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

    Click here