СИСТЕМА БЕССТУПЕНЧАТОЙ ТРАНСМИССИИ (для моделей с 8NR-FTS), Diagnostic DTC:P282413

DTC Code DTC Name
P282413 Pressure Control Solenoid "J" Circuit Open

DESCRIPTION

According to current from the ECM, the shift solenoid valve SLP controls primary pulley pressure in accordance with the requested gear ratio to perform gear ratio changes.

A0030HRC04
*1 Spool Valve *2 Sleeve
*3 Solenoid Coil - -
*a Hydraulic Pressure *b Current Flow to Solenoid
DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P282413 Pressure Control Solenoid "J" Circuit Open

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other


  1. The vehicle is being driven.

  2. An open or short in the shift solenoid valve SLP circuit is detected.

  3. 1 second or more

  4. 1-trip detection logic

  • Wire harness or connector

  • Continuously variable transaxle assembly (Shift solenoid valve SLP)

  • ECM

 Comes on DTC stored

SAE Code:

P2822

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SLP circuit. If there is an open or short in the shift solenoid valve SLP circuit, the ECM detects the malfunction, illuminates the MIL and stores this DTC.

WIRING DIAGRAM

A002ZRPE21
*a Shift Solenoid Valve SLP
*b Continuously Variable Transaxle Assembly (Transmission Wire)

CAUTION / NOTICE / HINT

Tech Tips

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Perform the D position test in Road Test.

    Click here

  2. Check for DTCs again.

    Click here

PROCEDURE


  1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLP)


    1. A0030OTC10
      *a

      Component without harness connected

      (Transmission Wire)

      Disconnect the B185 transmission wire connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4 (SLP+) - 11 (SLP-) 20°C (68°F) 5.0 to 5.6 Ω
      4 (SLP+) - Body ground and other terminals Always 10 kΩ or higher
      11 (SLP-) - Body ground and other terminals Always 10 kΩ or higher

    3. Connect the B185 transmission wire connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    1. Disconnect the B208 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B208-11 (SLP+) - B208-10 (SLP-) 20°C (68°F) 5.0 to 5.6 Ω
      B208-11 (SLP+) - Body ground and other terminals Always 10 kΩ or higher
      B208-10 (SLP-) - Body ground and other terminals Always 10 kΩ or higher

    3. Connect the B208 ECM connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

    OK

  3. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM INITIALIZATION Click here

  4. REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY


    1. Replace the continuously variable transaxle assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM INITIALIZATION Click here