СИСТЕМА БЕССТУПЕНЧАТОЙ ТРАНСМИССИИ (для моделей с 8NR-FTS), Diagnostic DTC:P071011

DTC Code DTC Name
P071011 Transmission Fluid Temperature Sensor "A" Circuit Short To Ground

DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature into a resistance value for use by the ECM.

The sensor resistance changes with the CVT fluid temperature. As the temperature rises, the sensor resistance decreases. The ECM applies voltage to the temperature sensor through ECM terminal THO1 and calculates the fluid temperature based on the voltage signal.

Tech Tips

The CVT fluid temperature is likely to increase under conditions such as towing, climbing hills and in traffic.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071011 Transmission Fluid Temperature Sensor "A" Circuit Short To Ground

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other


  1. Always

  2. Short in CVT fluid temperature sensor circuit

  3. 0.5 seconds

  4. 1-trip detection logic

  • Wire harness or connector

  • Continuously variable transaxle assembly (CVT fluid temperature sensor)

  • ECM

 Comes on DTC stored

SAE Code:

P0712

MONITOR DESCRIPTION

The CVT fluid temperature sensor converts the CVT fluid temperature to an electrical resistance value. Based on the resistance, the ECM determines the CVT fluid temperature and can detect a short to ground in the CVT fluid temperature circuit. If the resistance value of the CVT fluid temperature is less than 79 Ω*, the ECM interprets this as a malfunction of the CVT fluid temperature sensor or wiring, illuminates the MIL and stores a DTC.

*: 150°C (302°F) or more is indicated regardless of the actual CVT fluid temperature.

Tech Tips

The CVT fluid temperature can be checked in the Data List.

WIRING DIAGRAM

A0030K2E11
*a OIL
*b CVT Fluid Temperature Sensor
*c Transmission Wire
*d Continuously Variable Transaxle Assembly

CAUTION / NOTICE / HINT

Tech Tips

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Turn the ignition switch to ON and wait for 3 seconds or more.

  2. Check for DTCs again.

    Click here

PROCEDURE


  1. READ VALUE USING GTS (A/T OIL TEMPERATURE NO.1)


    1. Warm up the engine.

    2. Connect the GTS to the DLC3.

    3. Turn the ignition switch to ON.

    4. Turn the GTS on.

    5. Enter the following menus: Powertrain / Transmission / Data List.

    6. According to the display on the GTS, read the Data List.


      Powertrain > Transmission > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      A/T Oil Temperature No.1 CVT fluid temperature sensor value

      Min.: -40°C (-40°F)

      Max.: 150°C (302°F)

      • Approximately 100°C (212°F): After stall speed test

      • Equal to ambient temperature: After cold soak

      		 If the value is -40°C (-40°F) or 150°C (302°F) or more, the CVT fluid temperature sensor circuit is open or shorted.

      Powertrain > Transmission > Data List
      Tester Display
      A/T Oil Temperature No.1
      Result
      Result Proceed to
      Data List value is not normal A
      Data List value is normal B

    B

    REPLACE ECM Click here

    A

  2. INSPECT TRANSMISSION WIRE (CVT FLUID TEMPERATURE SENSOR)


    1. A0030OTC37
      *a

      Component without harness connected

      (Transmission Wire)

      Disconnect the B185 transmission wire connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (OIL) - 7 (E2) Always 79 Ω to 156 kΩ
      1 (OIL) - Body ground and other terminals Always 10 kΩ or higher
      7 (E2) - Body ground and other terminals Always 10 kΩ or higher

      Tech Tips

      If the resistance is out of the specified range at any of the CVT fluid temperatures shown in the table below, the driveability of the vehicle may decrease.

      CVT Fluid Temperature Specified Condition
      10°C (50°F) 5.6 to 7.3 kΩ
      25°C (77°F) 3.5 kΩ
      110°C (230°F) 0.22 to 0.27 kΩ

    3. Connect the B185 transmission wire connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    1. Disconnect the B208 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B208-84 (THO1) - B208-83 (ETHO) Always 79 Ω to 156 kΩ
      B208-84 (THO1) - Body ground and other terminals Always 10 kΩ or higher
      B208-83 (ETHO) - Body ground and other terminals Always 10 kΩ or higher

    3. Connect the B208 ECM connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

    OK

  4. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM INITIALIZATION Click here

  5. REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY


    1. Replace the continuously variable transaxle assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM INITIALIZATION Click here

  6. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM INITIALIZATION Click here