DATA LIST
Tech Tips
By reading the Data List displayed on the GTS, you can check values, including those of the switches, sensors, and actuators, without removing any parts. Reading the Data List as the first step of troubleshooting is one method of shortening diagnostic time.
Note
In the table below, the values listed under Normal Conditions are for reference only. Do not depend solely on these values when determining whether or not a part is faulty.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Check the values by referring to the following table.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Notes |
|---|---|---|---|
| Vehicle Speed | Vehicle speed: Min.: 0 km/h, Max.: 255 km/h |
Actual vehicle speed | Speed indicated on speedometer |
| Engine Speed | Engine speed: Min.: 0 rpm, Max.: 16383.75 rpm |
720 to 820 rpm: Idling (A/C off) After warming up engine |
- |
| MAP | Absolute pressure inside intake manifold: Min.: 0 kPa, Max.: 255 kPa |
|
- |
| Coolant Temp | Engine coolant temperature: Min.: -40°C, Max.: 215°C |
80 to 95°C (176 to 203°F): After warming up engine |
If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted |
| Intake Air | Intake air temperature: Min.: -40°C, Max.: 215°C |
Equivalent to temperature at intake manifold | If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted |
| Engine Run Time | Engine run time: Min.: 0 sec., Max.: 65535 sec. |
Time after the ignition switch turned to ON | Time passed since the ignition switch was turned to ON. |
| Battery Voltage | Battery voltage: Min.: 0 V, Max.: 65.5 V |
11 to 14 V | - |
| Glow Indicator Supported | Status of the glow indicator supported: Unsupp or Supp |
Supp | - |
| Glow Indicator | Status of the glow indicator: ON or OFF |
- | - |
| Accel Position | Accelerator pedal position: Min.: 0%, Max.: 100% |
|
- |
| Accel Sens. No.1 Volt % | Absolute Accelerator Pedal Position No. 1: Min.: 0%, Max.: 100% |
|
Read value with ignition switch ON (Do not start engine) |
| Accel Sens. No.2 Volt % | Absolute Accelerator Pedal Position No. 2: Min.: 0%, Max.: 100% |
|
Read value with ignition switch ON (Do not start engine) |
| Diesel Throttle Learn Status | Diesel throttle learning history: OK or NG |
OK | - |
| Throttle Step Position | Throttle step position: Min.: 0 step, Max.: 255 step |
|
Read value with ignition switch ON (Do not start engine) |
| Injection Volume | Injection volume: Min.: 0 mm3/st, Max.: 1279.98 mm3/st |
3 to 11 mm3/st: Idling |
- |
| Inj. FB Vol. for Idle | Idle stability status integral control volume: Min.: -80 mm3/st, Max.: 79 mm3/st |
- | - |
| Injection Timing | Injection timing: Min.: 0°CA, Max.: 51°CA |
- | - |
| Fuel Temperature | Fuel temperature: Min.: -40°C, Max.: 215°C |
Actual fuel temperature | If value -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted |
| Starter Signal | Starter signal: ON or OFF |
ON: Cranking | - |
| Stop Light Switch | Stop light switch: ON or OFF |
|
- |
| A/C Signal | A/C signal: ON or OFF |
ON: A/C switch is turned ON | - |
| Throttle Open Switch | Throttle open switch: ON or OFF |
ON: Throttle valve fully open | - |
| Check Mode | Check mode: ON or OFF |
ON: Check mode ON | |
| SPD Test Result | Check mode result for vehicle speed sensor: Compl or Incmpl |
- | - |
| Complete Parts Monitor | Comprehensive component monitor: Not Avl or Avail |
- | - |
| Fuel System Monitor | Fuel system monitor: Not Avl or Avail |
- | - |
| Misfire Monitor | Misfire monitor: Not Avl or Avail |
- | - |
| EGR/VVT Monitor | EGR/VVT monitor: Not Avl or Avail |
- | - |
| EGR/VVT Monitor | EGR/VVT monitor: Compl or Incmpl |
- | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor: Not Avl or Avail |
- | - |
| O2S(A/FS) Heater Monitor | O2S (A/FS) heater monitor: Compl or Incmpl |
- | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor: Not Avl or Avail |
- | - |
| O2S(A/FS) Monitor | O2S (A/FS) monitor: Compl or Incmpl |
- | - |
| A/C Monitor | A/C monitor: Not Avl or Avail |
- | - |
| A/C Monitor | A/C monitor: Compl or Incmpl |
- | - |
| 2nd Air Monitor | 2nd air monitor: Not Avl or Avail |
- | - |
| 2nd Air Monitor | 2nd air monitor: Compl or Incmpl |
- | - |
| EVAP Monitor | EVAP monitor: Not Avl or Avail |
- | - |
| EVAP Monitor | EVAP monitor: Compl or Incmpl |
- | - |
| Heated Catalyst Monitor | Heated catalyst monitor: Not Avl or Avail |
- | - |
| Heated Catalyst Monitor | Heated catalyst monitor: Compl or Incmpl |
- | - |
| Catalyst Monitor | Catalyst monitor: Not Avl or Avail |
- | - |
| Catalyst Monitor | Catalyst monitor: Compl or Incmpl |
- | - |
| # Codes (Include History) | Number of codes: Min.: 0, Max.: 255 |
0 | This is the number of DTCs stored. |
| MIL | MIL status: ON or OFF |
OFF | - |
| Time after DTC Cleared | Time after DTCs cleared: Min.: 0 minutes, Max.: 65535 minutes |
Time after DTCs cleared | Time elapsed since the DTCs were cleared (or shipment from the factory). |
| Distance from DTC Cleared | Distance driven after DTCs cleared: Min.: 0 km, Max.: 65535 km |
Distance driven after DTCs cleared |
|
| Warmup Cycle Cleared DTC | Warmup cycles after DTCs cleared: Min.: 0, Max.: 255 |
- |
|
| OBD Requirements | Identifying OBD requirement | - | - |
| Number of Emission DTC | Number of emissions-related DTCs | - | - |
| TC and TE1 | TC and TE1 connection status for Active Test: ON or OFF |
- | When the "Connect the TC and TE1" Active Test is performed, the system behaves as if TC and CG were connected. |
| ACT VSV | A/C cut status: ON or OFF |
- | "Control the A/C Cut Signal" Active Test support data. |
| Model Code | Model code | - | Identifying model code |
| Engine Type | Engine type | - | Identifying engine type: 5LE |
| Cylinder Number | Cylinder number: Min.: 0, Max.: 255 |
- | Identifying cylinder number: 4 |
| Transmission Type | Transmission type | - | - |
| Destination | Destination | - | Identifying destination |
| Model Year | Model year: Min.: 1900, Max.: 2155 |
- | Identifying model year: 20## |
Normal Condition: If no idling conditions are specified, the shift lever should be in neutral, and the A/C switch and all accessory switches should be off.
ACTIVE TEST
Tech Tips
Performing an Active Test enables components including the relays, VSV (Vacuum Switching Valve), and actuators, to be operated without removing any parts. The Active Test can be performed with the GTS. Active Test as a first step of troubleshooting is one method of shortening diagnostic time.
The Data List can be displayed during Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Perform the Active Tests by referring to the following table.
| Tester Display | Test Part | Control Range | Diagnostic Notes |
|---|---|---|---|
| Control the A/C cut signal | Control the A/C cut signal | ON/OFF | Test is possible when the following conditions are met:
|
| Connect the TC and TE1 | Turn on the TC and TE1 connection | ON/OFF | Test is possible when the following conditions are met:
|
| Control the Electric Cooling Fan | Control the cooling fan operation | ON/OFF | Test is possible when the following conditions are met:
|