LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY (for TMMK Made LHD) REMOVAL


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)

    Click here

  4. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)

    Click here

  5. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. B000M41E01

      Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Be sure to hold the part of the rear seat cushion assembly directly next to the rear seat cushion lock hooks when lifting it up. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

    2. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  6. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. B000LZB

      Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  7. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide.

    2. Disconnect the connector.

    3. B000HU6

      Remove the 2 bolts.

    4. Disengage the hook and remove the rear side seatback assembly LH.

  8. REMOVE FRONT DOOR SCUFF PLATE LH


    1. B000JR7E01

      Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.

    2. Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.

    3. Disengage the 6 claws (C) to remove the front door scuff plate LH.

  9. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the front door opening trim weatherstrip.

  10. REMOVE REAR DOOR SCUFF PLATE LH


    1. B000H06E01

      Disengage the claw (A) in the direction indicated by the arrow (1) shown in the illustration.

    2. Disengage the claw (B) in the direction indicated by the arrow (2) shown in the illustration.

    3. Disengage the 4 claws (C) to remove the rear door scuff plate LH.

      Tech Tips

      Disengage the claws from the front side of the rear door scuff plate LH.

  11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the rear door opening trim weatherstrip LH.

  12. REMOVE LAP BELT OUTER ANCHOR COVER


    1. B000K92

      Disengage the 3 claws and remove the lap belt outer anchor cover.

  13. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. B000IQ2

      Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.

  14. REMOVE CENTER PILLAR LOWER GARNISH LH


    1. B000NG5

      Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.

  15. REMOVE LUGGAGE COMPARTMENT DOOR COVER


    1. B000HTS

      Remove the 13 clips and luggage compartment door cover.

  16. REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER LH


    1. B000K42

      Remove the 2 clips.

    2. Disengage the clip and remove the luggage compartment door hinge cover LH.

  17. REMOVE SPARE WHEEL COVER ASSEMBLY


    1. Remove the spare wheel cover assembly.

  18. REMOVE REAR FLOOR FINISH PLATE


    1. B000NKV

      Remove the 5 clips.

    2. B000J8C

      Disengage the 4 clips and remove the rear floor finish plate as shown in the illustration.

  19. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. B000NA4E01
      Text in Illustration
      *a Pin

      Push in the pin and remove the No. 1 luggage compartment trim hook.

  20. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH


    1. B000HM4

      Remove the 2 clips.

    2. Disengage the fastener and remove the luggage compartment inner trim cover LH.

  21. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. B000MSZ

      Remove the screw.

    2. B000NNN

      Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.

    3. B000J3V

      Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.

  22. REMOVE LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY


    1. B000IFB

      Disengage the 2 clamps.

    2. B000JQP

      Using a clip remover, disengage the clamp and disconnect the wire harness.

    3. B000IM1

      Using a clip remover, disengage the 2 clamps and remove the 2 scuff plate clips.

    4. Turn back the floor carpet so that the luggage door lock control cable sub-assembly and fuel lid lock control cable sub-assembly can be removed.

    5. B000LT4

      Disengage the guide as shown in the illustration.

    6. B000M4Y

      Disconnect the luggage door lock control cable sub-assembly.

    7. B000HTK

      Disengage the clamp and disconnect the luggage door lock control cable sub-assembly.

    8. B000LX7E02
      Text in Illustration
      *a Cutout
      *b Guide (A)

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides (A), and then pull the fuel filler opening lid lock retainer.

    9. B000IDNE02
      Text in Illustration
      *a Cutout
      *b Guide (B)

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides (B), and then pull the fuel filler opening lid lock retainer.

    10. B000ILRE02
      Text in Illustration
      *a Cutout
      *b Guide (C)
      *c Guide (B)

      Pull out the fuel filler opening lid lock retainer with both guides (B) and (C) aligned with the cutouts.

    11. B000H1N

      Disengage the 2 claws and remove the fuel filler opening lid lock retainer.

    12. Disengage the 10 clamps and remove the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

      B000L5JE01
      Text in Illustration
      *1 Fuel Lid Lock Control Cable Sub-assembly *2 Luggage Door Lock Control Cable Sub-assembly

    13. Using a knife, cut off the clamp as shown in the illustration.

      B000INAE02
      Text in Illustration
      *a Tape *b Cut

      Note

      Be careful not to damage the vehicle fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

    14. Remove the clamp.

    15. Remove the 3 pieces of tape and fuel lid lock control cable sub-assembly.