LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY (for TMC, TMMR Made LHD) REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)

    Click here

  3. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)

    Click here

  4. REMOVE FRONT DOOR SCUFF PLATE LH


    1. B000N47

      Disengage the 10 claws and remove the front door scuff plate LH.

  5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the front door opening trim weatherstrip.

  6. REMOVE REAR DOOR SCUFF PLATE LH


    1. B000H7A

      Disengage the 6 claws and remove the rear door scuff plate LH.

      Tech Tips

      Disengage the claws from the rear side of the scuff plate.

  7. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the rear door opening trim weatherstrip LH.

  8. REMOVE LAP BELT OUTER ANCHOR COVER


    1. B000K92

      Disengage the 3 claws and remove the lap belt outer anchor cover.

  9. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. B000IQ2

      Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.

  10. REMOVE CENTER PILLAR LOWER GARNISH LH


    1. B000NG5

      Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.

  11. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)


    1. B000IRWE01

      Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Be sure to hold the part of the rear seat cushion assembly directly next to the rear seat cushion lock hooks when lifting it up. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

    2. w/ Seat Heater System:


      1. Disconnect the connector.

      2. B000KQW

        Disengage the 2 clamps.

    3. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  12. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)


    1. B000LZB

      Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  13. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)


    1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide LH.

    2. B000HI6

      Remove the bolt.

    3. Disengage the hook and remove the rear side seatback assembly LH.

      Note

      Be careful not to damage the vehicle body.

  14. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)


    1. B000HUCE01

      Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Be sure to hold the part of the rear seat cushion assembly directly next to the rear seat cushion lock hooks when lifting it up. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

    2. Disconnect the 2 seat heater connectors.

    3. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  15. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)


    1. B000LZB

      Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  16. REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type)

  17. REMOVE REAR SEATBACK COVER (for Reclining Seat Type)


    1. B000HOH

      Disengage the 4 claws and remove the 2 rear seatback covers.

      Tech Tips

      Use the same procedure as for the LH side.

  18. REMOVE REAR SEATBACK ASSEMBLY LH (for Reclining Seat Type)


    1. w/ Rear Seat Side Airbag:


      1. Disconnect each connector and clamp from the child restraint seat anchor bracket sub-assembly LH.

    2. Disengage the 2 rear seat belts from the 2 rear seat shoulder belt guides.

    3. B000HLQ

      Disengage the 2 hooks and disconnect the cover.

    4. Remove the 2 nuts, 2 bolts and rear seatback assembly LH.

  19. REMOVE REAR SEAT SIDE GARNISH LH (for Reclining Seat Type)


    1. B000MZ6

      Remove the bolt.

    2. Disengage the claw, 2 clips and guide and remove the rear seat side garnish LH.

  20. REMOVE LUGGAGE COMPARTMENT DOOR COVER


    1. B000MQQ

      Remove the 13 clips and luggage compartment door cover.

  21. REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER LH


    1. B000IW4E01
      Text in Illustration
      *a Clip (A)
      *b Clip (B)

      Remove the 3 clips (A).

    2. Disengage the clip (B) and remove the luggage compartment door hinge cover LH.

  22. REMOVE LUGGAGE COMPARTMENT FLOOR MAT


    1. Remove the luggage compartment floor mat.

  23. REMOVE BAGGAGE HOLDER NET (w/ Partition Net)


    1. Remove the baggage holder net.

  24. REMOVE REAR FLOOR FINISH PLATE


    1. B000KBF

      Remove the 5 clips.

    2. B000IEE

      Disengage the 4 clips and remove the rear floor finish plate.

  25. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. B000KW7E01
      Text in Illustration
      *1 Pin

      Push the pin and remove the No. 1 luggage compartment trim hook.

  26. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH


    1. B000MUP

      Remove the 3 clips.

    2. Disengage the fastener and remove the luggage compartment inner trim cover LH.

  27. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. B000MSZ

      Remove the screw.

    2. B000NNN

      Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.

    3. B000J3V

      Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.

  28. REMOVE LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY


    1. B000IFB

      Disengage the 2 clamps.

    2. B000JQP

      Disengage the clamp and disconnect the wire harness.

    3. B000IM1

      Disengage the 2 clamps and remove the 2 scuff plate clips.

    4. Turn back the floor carpet so that the luggage door lock control cable sub-assembly and fuel lid lock control cable sub-assembly can be removed.

    5. B000J80

      Disengage the guide as shown in the illustration.

    6. B000NBH

      Disconnect the luggage door lock control cable sub-assembly.

    7. B000J63

      Disengage the clamp and disconnect the luggage door lock control cable sub-assembly.

    8. B000LX7E01
      Text in Illustration
      *1 Cutout
      *2 Guide <A>

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides <A>, and then pull the fuel filler opening lid lock retainer.

    9. B000IDNE01
      Text in Illustration
      *1 Cutout
      *2 Guide <B>

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides <B>, and then pull the fuel filler opening lid lock retainer.

    10. B000ILRE01
      Text in Illustration
      *1 Cutout
      *2 Guide <C>
      *3 Guide <B>

      Pull out the fuel filler opening lid lock retainer with both guides <B> and <C> aligned with the cutouts.

    11. B000H1N

      Disengage the 2 claws and remove the fuel filler opening lid lock retainer.

    12. Disengage the 10 clamps and remove the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

      B000KSTE01
      Text in Illustration
      *1 Fuel Lid Lock Control Cable Sub-assembly *2 Luggage Door Lock Control Cable Sub-assembly

    13. Using a knife, cut off the clamp as shown in the illustration.

      B000INAE01
      Text in Illustration
      *1 Tape - -
      *a Cut - -

      Note

      Be careful not to damage the vehicle fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

    14. Remove the clamp.

    15. Remove the 3 pieces of tape and luggage door lock control cable sub-assembly.