LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY (for RHD) INSTALLATION


  1. INSTALL LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY


    1. Engage the 10 clamps and install the luggage door lock control cable sub-assembly.

    2. Engage the 2 clamps and connect the luggage door lock control cable sub-assembly.

    3. Connect the luggage door lock control cable sub-assembly.

    4. B000IBU

      Engage the guide as shown in the illustration.

    5. B000K7ZE01
      Text in Illustration
      *1 Tape
      *2 Fuel Lid Lock Control Cable Sub-assembly
      *3 Luggage Door Lock Control Cable Sub-assembly

      Install the luggage door lock control cable sub-assembly to the fuel lid lock control cable sub-assembly with the 2 pieces of tape as shown in the illustration.

      Reference Measurement
      Area Measurement
      a 295 to 305 mm (11.6 to 12.0 in.)
      b 935 to 955 mm (36.8 to 37.6 in.)

      Note


      • Wrap tape around the designated positions 1 to 3 times.

      • Make sure that the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly are not kinked.

    6. Return the floor carpet to the original position.

    7. Engage the 2 clamps and install the 2 scuff plate clips.

    8. Engage the 3 clamps to connect the wire harness.

  2. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. B000N2OE01
      Text in Illustration
      *1 Luggage Door Lock Control Cable Sub-assembly
      *2 Fuel Lid Lock Control Cable Sub-assembly

      Connect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly to the fuel lid lock open lever sub-assembly.

    2. B000KPO

      Engage the guide and install the fuel lid lock open lever sub-assembly as shown in the illustration.

    3. Install the screw.

  3. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH


    1. Install the 3 clips.

    2. Engage the fastener and install the luggage compartment inner trim cover RH.

  4. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. B000H4EE01
      Text in Illustration
      *1 Pin

      Engage the pin to install the No. 1 luggage compartment trim hook.

  5. INSTALL REAR FLOOR FINISH PLATE


    1. B000K2P

      Engage the 4 clips and install the rear floor finish plate.

    2. Install the 5 clips.

  6. INSTALL BAGGAGE HOLDER NET (w/ Partition Net)


    1. Install the baggage holder net.

  7. INSTALL LUGGAGE COMPARTMENT FLOOR MAT


    1. Install the luggage compartment floor mat.

  8. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  9. INSTALL LUGGAGE COMPARTMENT DOOR COVER


    1. B000MQQ

      Install the luggage compartment door cover with the 13 clips.

  10. INSTALL REAR SIDE SEATBACK ASSEMBLY RH


    1. Place the rear side seatback assembly RH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Engage the hook to install the rear side seatback assembly RH with the bolt.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    3. Connect the rear seat outer belt assembly to the rear seat shoulder belt guide RH.

  11. INSTALL REAR SEAT CUSHION LOCK HOOK


    1. B000HKU

      Engage the 2 claws to install a new rear seat cushion lock hook as shown in the illustration.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure as for the LH side.

  12. INSTALL REAR SEAT CUSHION ASSEMBLY


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. w/ Seat Heater System:


      1. Engage the 2 clamps.

      2. Connect the connector.

    3. B000LR0

      Engage the 2 hooks of the rear seat cushion assembly to the vehicle body as shown in the illustration.

    4. Confirm that the rear seat cushion assembly is firmly installed.

      Note

      When installing the rear seat cushion assembly, make sure that the seat belt buckles are not under the rear seat cushion assembly.

  13. INSTALL CENTER PILLAR LOWER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  14. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  15. INSTALL LAP BELT OUTER ANCHOR COVER

    Tech Tips

    Use the same procedure as for the LH side Click here.

  16. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. B000KSGE01
      Text in Illustration
      *1 Alignment Mark (Blue)

      Align the alignment mark (Blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  17. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  18. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. B000HULE01
      Text in Illustration
      *1 Alignment Mark (White)

      Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  19. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  20. INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)

    Click here

  21. INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)

    Click here