LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY (for RHD) REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)

    Click here

  3. REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat)

    Click here

  4. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  6. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  7. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  8. REMOVE LAP BELT OUTER ANCHOR COVER

    Tech Tips

    Use the same procedure as for the LH side Click here.

  9. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  10. REMOVE CENTER PILLAR LOWER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  11. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. B000IRWE01

      Lift up the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks on the front side of the rear seat cushion assembly from the 2 rear seat cushion lock hooks.

      Standard Measurement
      a 100 mm (3.94 in.) or less

      Note

      Be sure to hold the part of the rear seat cushion assembly directly next to the rear seat cushion lock hooks when lifting it up. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

    2. w/ Seat Heater System:


      1. Disconnect the connector.

      2. B000KQW

        Disengage the 2 clamps.

    3. Pass the 2 rear seat inner belt assemblies through the rear seat cushion assembly and remove the rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  12. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. B000LZB

      Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  13. REMOVE REAR SIDE SEATBACK ASSEMBLY RH


    1. Disconnect the rear seat outer belt assembly from the rear seat shoulder belt guide RH.

    2. B000K82

      Remove the bolt.

    3. Disengage the hook and remove the rear side seatback assembly RH.

      Note

      Be careful not to damage the vehicle body.

  14. REMOVE LUGGAGE COMPARTMENT DOOR COVER


    1. B000MQQ

      Remove the 13 clips and luggage compartment door cover.

  15. REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  16. REMOVE LUGGAGE COMPARTMENT FLOOR MAT


    1. Remove the luggage compartment floor mat.

  17. REMOVE BAGGAGE HOLDER NET (w/ Partition Net)


    1. Remove the baggage holder net.

  18. REMOVE REAR FLOOR FINISH PLATE


    1. B000KBF

      Remove the 5 clips.

    2. B000IEE

      Disengage the 4 clips and remove the rear floor finish plate.

  19. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. B000NQLE01
      Text in Illustration
      *1 Pin

      Push the pin and remove the No. 1 luggage compartment trim hook.

  20. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER RH


    1. B000MZ5

      Remove the 3 clips.

    2. Disengage the fastener and remove the luggage compartment inner trim cover RH.

  21. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. B000IA2

      Remove the screw.

    2. B000KYN

      Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.

    3. B000N2O

      Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.

  22. REMOVE LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY


    1. B000L9R

      Disengage the 2 clamps.

    2. B000N6P

      Disengage the clamp and disconnect the wire harness.

    3. B000IYA

      Disengage the 2 clamps and remove the 2 scuff plate clips.

    4. Turn back the floor carpet so that the luggage door lock control cable sub-assembly can be removed.

    5. B000I18E01
      Text in Illustration
      *1 Tape
      *2 Fuel Lid Lock Control Cable Sub-assembly
      *3 Luggage Door Lock Control Cable Sub-assembly

      Remove the 2 pieces of tape that connect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

    6. B000J80

      Disengage the guide as shown in the illustration.

    7. B000NBH

      Disconnect the luggage door lock control cable sub-assembly.

    8. B000I5V

      Disengage the 2 clamps and disconnect the luggage door lock control cable sub-assembly.

    9. Disengage the 10 clamps and remove the luggage door lock control cable sub-assembly.

      B000IS5E01
      Text in Illustration
      *1 Luggage Door Lock Control Cable Sub-assembly *2 Fuel Lid Lock Control Cable Sub-assembly