HOOD (for TMC, TMMR Made) REASSEMBLY


  1. INSTALL HOOD SUPPORT ASSEMBLY LH

    Note


    • Avoid touching the piston rod as much as possible to prevent foreign matter from attaching to it. Be sure to hold the cylinder while servicing.

    • Do not wear cotton gloves or other similar materials when handling the piston rod. Fibers may attach to the rod and result in gas leaks.

    • In order to prevent the piston rod from deforming, do not apply any horizontal load to the door stay.


    1. When reusing the hood support assembly:


      1. B000N09

        Install the 2 stop rings to the hood support assembly.

    2. B000MOZ

      Install the hood support assembly.

      Note

      Install the hood support assembly while supporting the hood by hand.

    3. Check that the hood support assembly is engaged in the ball joint and it cannot be pulled out.

  2. INSTALL HOOD SUPPORT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  3. CONNECT WASHER HOSE ASSEMBLY


    1. B000LBL

      Engage the 6 clamps to connect the washer hose assembly.

  4. INSTALL WASHER NOZZLE SUB-ASSEMBLY


    1. Connect a new washer nozzle sub-assembly to the washer hose.

    2. B000H1QE01

      Engage the 2 claws to install the washer nozzle sub-assembly as shown in the illustration.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  5. INSPECT WASHER NOZZLE SUB-ASSEMBLY


    1. for TMC, TMMR Made:


      1. Operate the washer nozzle sub-assembly and check the position that the washer fluid hits the windshield.

        Standard
        Washer fluid hits the windshield in the areas shown in the illustration.
        B000HIZE01
        Standard Clearance
        Area Measurement Area Measurement
        A 300.0 mm (11.8 in.) B 145.0 mm (5.71 in.)
        C 170.0 mm (6.69 in.) - -
        Text in Illustration
        *a Upper Limit *b Standard
        *c Lower Limit - -

        Tech Tips

        If the result is not as specified, replace the washer nozzle sub-assembly.

    2. for TMMK Made:


      1. Operate the washer nozzle sub-assembly and check the position that the washer fluid hits the windshield.

        Standard
        Washer fluid hits the windshield in the areas shown in the illustration.
        B000HIZE10
        Standard Clearance
        Area Measurement Area Measurement
        A 300.0 mm (11.8 in.) B 145.0 mm (5.71 in.)
        C 175.0 mm (6.89 in.) - -
        Text in Illustration
        *a Upper Limit *b Standard
        *c Lower Limit - -

        Tech Tips

        If the result is not as specified, replace the washer nozzle sub-assembly.

  6. ADJUST WASHER NOZZLE SUB-ASSEMBLY


    1. Select a washer nozzle so that the contact area is within the standard. Replace the washer nozzle with the selected one.

      B000HRZE03
      Text in Illustration
      *a Washer Fluid Spray Angle *b Part Number

  7. INSTALL HOOD INSULATOR


    1. B000HEO

      Engage the 2 guides.

    2. Install the hood insulator with 7 new clips.

  8. INSTALL HOOD TO RADIATOR SUPPORT SEAL


    1. B000MB9

      Engage the 8 clips to install the hood to radiator support seal.

  9. INSTALL FRONT HOOD MOULDING ASSEMBLY


    1. Install the front hood moulding assembly with the 7 nuts.

  10. INSTALL HOOD CENTER CUSHION


    1. B000MKE

      Engage the 2 claws to install 2 new hood center cushions.