LUGGAGE DOOR HINGE TORSION BAR (for TMC, TMMR Made) INSTALLATION

Note

After installing the torsion bar, use your hand to open and close the luggage door. Make sure the luggage door can open and close smoothly.


  1. INSTALL LUGGAGE COMPARTMENT DOOR TORSION BAR SUPPORT


    1. B000HKZ

      Install a new luggage compartment door torsion bar support as shown in the illustration.

  2. INSTALL LUGGAGE DOOR HINGE TORSION BAR RH


    1. Check the identification mark on the luggage door hinge torsion bar RH.

      Color
      Green
    2. B000K5TE01
      Text in Illustration
      *a Installation Hole
      *b Installation Hole (For Adjustment)

      Set the tip of the luggage door hinge torsion bar RH in the center installation hole. The upper and lower installation holes are used for adjustment.

    3. B000J34

      Connect the luggage door hinge torsion bar RH to the left side of the vehicle body as shown in the illustration.

    4. B000HAQ

      Connect the luggage door hinge torsion bar RH to the luggage compartment door torsion bar support as shown in the illustration.

    5. B000H79E01

      Using SST, install the luggage door hinge torsion bar RH to the luggage door hinge and the right side of the vehicle body as shown in the illustration.

      SST
      09804-24010

    6. Remove the protective tape.

  3. INSTALL LUGGAGE DOOR HINGE TORSION BAR LH


    1. Check the identification mark on the luggage door hinge torsion bar RH.

      Color
      White
    2. B000JMNE01
      Text in Illustration
      *a Installation Hole
      *b Installation Hole (For Adjustment)

      Set the tip of the luggage door hinge torsion bar LH in the center installation hole. The upper and lower installation holes are used for adjustment.

    3. B000IXJ

      Connect the luggage door hinge torsion bar LH to the right side of the vehicle body as shown in the illustration.

    4. B000LAM

      Connect the luggage door hinge torsion bar LH to the luggage compartment door torsion bar support as shown in the illustration.

    5. B000HMPE01

      Using SST, install the luggage door hinge torsion bar LH to the luggage door hinge and the left side of the vehicle body as shown in the illustration.

      SST
      09804-24010
    6. B000HEJ

      Engage the 2 claws as shown in the illustration.

    7. for Fold Down Seat Type:


      1. B000L3LE01

        Connect the rear seatback lock assembly LH (rear seat lock control cable LH) and engage the hook in the order indicated in the illustration.

      2. Engage the clamp.

        Tech Tips

        Use the same procedure as for the LH side and RH side.

    8. Remove the protective tape.

  4. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER LH


    1. Engage the 4 claws and install the luggage compartment door hinge cover LH.

  5. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER RH

    Tech Tips

    Use the same procedure as for the LH side.

  6. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH


    1. Install the 3 clips.

    2. Engage the fastener and install the luggage compartment inner trim cover LH.

  7. INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER RH


    1. Install the 3 clips.

    2. Engage the fastener and install the luggage compartment inner trim cover RH.

  8. INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. B000MS8E01
      Text in Illustration
      *1 Pin

      Engage the 2 pins to install the 2 No. 1 luggage compartment trim hooks.

  9. INSTALL REAR FLOOR FINISH PLATE


    1. B000K2P

      Engage the 4 clips and install the rear floor finish plate.

    2. Install the 5 clips.

  10. INSTALL BAGGAGE HOLDER NET (w/ Partition Net)


    1. Install the baggage holder net.

  11. INSTALL LUGGAGE COMPARTMENT FLOOR MAT


    1. Install the luggage compartment floor mat.