BACK WINDOW GLASS (for TMMK Made) REMOVAL


  1. REMOVE ROOF HEADLINING ASSEMBLY

    Click here

  2. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)


    1. B000H1H

      Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.

  3. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)


    1. B000IIN

      Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.

  4. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH


    1. B000N8L

      Remove the 2 nuts and child restraint seat anchor bracket sub-assembly LH.

  5. DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


    1. for Type A:


      1. B000H32

        Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.

    2. for Type B:


      1. B000LJR

        Remove the bolt and disconnect the floor anchor of the rear seat inner with center belt assembly LH.

  6. REMOVE CENTER STOP LIGHT SET


    1. B000H2KE01

      Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to disengage the 4 claws.

    2. B000IPH

      Turn the center stop light set 180 degrees as shown by the arrow in the illustration.

      Tech Tips

      This makes it easier to disconnect the connector.

    3. Disconnect the connector and remove the center stop light set.

  7. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER


    1. B000K4D

      Using a moulding remover, disengage the 2 claws and 2 guides to remove the child restraint seat tether anchor cover.

      Tech Tips

      Use the same procedure for the other 2 child restraint seat tether anchor covers.

  8. REMOVE REAR SEAT SHOULDER BELT COVER


    1. B000N9T

      Using a moulding remover, disengage the 2 claws and 4 guides and remove the rear seat shoulder belt cover.

      Tech Tips

      Use the same procedure for the other 2 rear seat shoulder belt covers.

  9. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    1. B000KXZE02
      Text in Illustration
      *a Protective Tape

      Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.

      Tech Tips

      Tape the tip of the pliers before use.

    2. Disengage the 5 guides.

    3. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.

  10. REMOVE BACK WINDOW GLASS SUB-ASSEMBLY


    1. Disconnect each connector.

    2. B000HQZE01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area around the installation position of the back window glass sub-assembly on the vehicle body to prevent it from being scratched.

    3. B000KRGE01
      Text in Illustration
      *a Cut Off

      Using a knife, cut off the back window outside moulding as shown in the illustration.

    4. B000IV4E01
      Text in Illustration
      *1 Matchmark

      Place matchmarks on the back window glass sub-assembly and vehicle body at the locations indicated in the illustration.

      Tech Tips

      Matchmarks are not necessary if the back window glass sub-assembly is not going to be reused.

    5. B000KMDE01
      Text in Illustration
      *1 Stopper
      *a Piano Wire

      Pass a piano wire between the vehicle body and back window glass sub-assembly from the interior.

    6. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

    7. Cut off the adhesive by pulling the piano wire around the back window glass sub-assembly.

      Note

      When removing the back window glass, take care not to damage the paint or interior and exterior ornaments.

    8. Disengage the back window glass stoppers.

      B000JZGE01
      Text in Illustration
      *A for 1-piece Type *B for 2-piece Type
      *1 No. 1 Back Window Glass Stopper *2 No. 2 Back Window Glass Stopper

      Note


      • The No. 1 back window glass stoppers and No. 2 back window glass stoppers are installed to the back window glass as shown in the illustration. Be careful not to damage the back window glass when cutting off the adhesive.

      • To prevent the back window glass sub-assembly from falling when performing this operation, be sure to hold the back window glass sub-assembly using suction cups.

      Tech Tips

      Depending on the vehicle, either 1-piece type or 2-piece type stoppers may be present.

    9. Using suction cups, remove the back window glass sub-assembly.

      Note


      • Be careful not to drop the back window glass sub-assembly.

      • Leave as much adhesive on the vehicle body as possible when removing the back window glass sub-assembly.

  11. REMOVE BACK WINDOW GLASS ADHESIVE DAM


    1. When reusing the back window glass:


      1. B000NIOE01
        Text in Illustration
        *A Back Side

        Using a scraper, remove the back window glass adhesive dam from the back side of the back window glass.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the back window glass adhesive dam with a new one.

  12. REMOVE BACK WINDOW OUTSIDE MOULDING


    1. When reusing the back window glass:


      1. B000K4OE01
        Text in Illustration
        *A Back Side

        Using a scraper, remove the back window outside moulding from the back side of the back window glass.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the back window outside moulding with a new one.

  13. REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 1-piece Type)


    1. When reusing the back window glass:


      1. B000H30E01
        Text in Illustration
        *A Back Side

        Using a scraper, remove the 2 No. 1 back window glass stoppers from the back side of the back window glass.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the 1-piece type No. 1 back window glass stoppers with new 2-piece type No. 1 and No. 2 back window glass stoppers.

  14. REMOVE NO. 2 BACK WINDOW GLASS STOPPER (for 2-piece Type)


    1. When reusing the back window glass:


      1. B000H30E01
        Text in Illustration
        *A Back Side

        Using a scraper, remove the 2 No. 2 back window glass stoppers from the back side of the back window glass.

        Note


        • Be careful not to damage the back window glass.

        • Be sure to replace the No. 2 back window glass stoppers with new ones.

  15. REMOVE NO. 1 BACK WINDOW GLASS STOPPER (for 2-piece Type)


    1. B000JPL

      Remove the 2 No. 1 back window glass stoppers.

      Note

      Be sure to replace the No. 1 back window glass stoppers with new ones.

  16. CLEAN BACK WINDOW GLASS


    1. Using a scraper, remove any remaining adhesive dam and adhesive residue from the back window glass.

      Note

      Be careful not to damage the back window glass.

    2. B000H2N

      Clean the outer circumference of the back window glass with a non-residue solvent.

      Note


      • Do not touch the back window glass surface after cleaning it.

      • Even if using a new back window glass, clean it with a non-residue solvent.

  17. CLEAN VEHICLE BODY


    1. B000K9LE07
      Text in Illustration
      *1 Adhesive
      *2 Vehicle Body

      Clean and shape the contact surface of the vehicle body.


      1. Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

        Note

        Be careful not to damage the vehicle body.

        Tech Tips

        Leave as much adhesive on the vehicle body as possible.

      2. Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.

        Tech Tips

        Even if all of the adhesive has been removed, clean the vehicle body.