WINDSHIELD GLASS (for TMC, TMMR Made) REMOVAL


  1. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. B000J8F

      Remove the nut and front wiper arm and blade assembly LH.

  2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. B000LCJ

      Remove the nut and front wiper arm and blade assembly RH.

  3. REMOVE FRONT FENDER TO COWL SIDE SEAL LH


    1. for TMC, TMMR Made:


      1. B000HOQ

        Disengage the 2 clips and 3 guides and remove the front fender to cowl side seal LH as shown in the illustration.

    2. for TMMK Made:


      1. B000KUD

        Disengage the 2 clips and guide and remove the front fender to cowl side seal LH as shown in the illustration.

  4. REMOVE FRONT FENDER TO COWL SIDE SEAL RH

    Tech Tips

    Use the same procedure as for the LH side.

  5. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. Disengage the 6 claws and guide as shown in the illustration.

      B000NRN

    2. Disengage the 8 guides and pull out the cowl top ventilator louver sub-assembly as shown in the illustration.

      B000KP5

  6. REMOVE INNER REAR VIEW MIRROR ASSEMBLY

    Click here

  7. REMOVE RAIN SENSOR (w/ Rain Sensor)

    Click here

  8. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. B000HXQ

      Disconnect the front door opening trim weatherstrip LH.

  9. REMOVE FRONT PILLAR GARNISH LH


    1. B000I9QE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

      Tech Tips

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    2. B000HANE01

      While pushing the tabs on the front pillar garnish clip in the direction indicated by the arrow (A) shown in the illustration, disengage the front pillar garnish clip.

    3. Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.

    4. B000KY7E01
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover
      *3 Curtain Shield Airbag Assembly

      Protect the curtain shield airbag assembly.


      1. Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

  10. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. B000J7V

      Disconnect the front door opening trim weatherstrip RH.

  11. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  12. REMOVE ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)


    1. B000LH6

      Using a moulding remover, disengage the 4 clips.

    2. Disconnect the connector and remove the roof console box assembly.

  13. REMOVE ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)


    1. B000IP9

      Using a moulding remover, disengage the 4 clips.

    2. Disconnect the connector and remove the roof console box assembly.

  14. REMOVE SPOT LIGHT ASSEMBLY


    1. B000N92E01
      Text in Illustration
      *a Front

      Using a moulding remover, disengage the 4 claws.

    2. Disconnect the connector and remove the spot light assembly.

  15. REMOVE ASSIST GRIP SUB-ASSEMBLY


    1. B000MKLE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips

      Tape the screwdriver tip before use.

    2. B000HXU

      Disengage the 2 clips and remove the assist grip sub-assembly.

    3. Remove the 2 clips from the vehicle body.

      Tech Tips

      Use the same procedure for the RH side.

  16. REMOVE REAR ASSIST GRIP ASSEMBLY LH


    1. B000KL4E01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

      Note

      Do not forcibly pry the assist grip covers to prevent them from being deformed.

      Tech Tips

      Tape the screwdriver tip before use.

    2. B000J7I

      Disengage the 2 clips and remove the rear assist grip assembly LH.

    3. Remove the 2 clips from the vehicle body.

  17. REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  18. REMOVE VISOR BRACKET COVER (for LH Side)


    1. B000MM7

      Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.

  19. REMOVE VISOR ASSEMBLY LH


    1. B000JXS

      Remove the 2 screws and visor assembly LH.

  20. REMOVE VISOR BRACKET COVER (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side.

  21. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  22. REMOVE VISOR HOLDER


    1. B000N4ME01

      Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Disengage the 2 claws and remove the visor holder.

      Tech Tips

      Use the same procedure for the other visor holder.

  23. REMOVE SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)


    1. Remove the sliding roof opening trim moulding.

  24. REMOVE ROOF HEADLINING ASSEMBLY


    1. Slightly lower the front section of the roof headlining assembly so that the windshield glass can be removed.

      Tech Tips

      It is not necessary to completely remove the roof headlining assembly.

  25. REMOVE WINDSHIELD GLASS SUB-ASSEMBLY


    1. w/ Window Deicer System:


      1. Disconnect the connector and disengage the clamp.

    2. w/ Heated Windshield Defroster System:


      1. Disconnect the 2 connectors and disengage the 2 clamps.

    3. B000LV9E01
      Text in Illustration
      *1 Protective Tape

      Apply protective tape to the area around the installation position of the windshield glass on the vehicle body to prevent it from being scratched.

    4. B000MOBE01
      Text in Illustration
      *1 Wooden Block
      *2 Plastic Sheet
      *3 Stopper
      *4 Piano Wire
      *5 Windshield Glass Retainer

      Pass a piano wire between the vehicle body and glass from the interior as shown in the illustration.

    5. Tie both wire ends to wooden blocks or similar objects that can serve as handles.

    6. Cut off the adhesive by pulling the piano wire around the windshield glass sub-assembly.

      Note


      • When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.

      • To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.

    7. B000LW9E01
      Text in Illustration
      *1 Matchmark

      Place matchmarks on the windshield glass sub-assembly and vehicle body on the locations indicated in the illustration.

      Tech Tips

      Matchmarks are not necessary if the windshield glass sub-assembly is not going to be reused.

    8. Disconnect the windshield glass stoppers and windshield glass retainers.

      B000H03E01
      Text in Illustration
      *A 1-piece Type *B 2-piece Type
      *1 No. 1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper
      *3 Windshield Glass Retainer - -

      Note


      • There are No. 1, No. 2 stoppers and windshield glass retainers on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.

      • To prevent the windshield glass from falling when performing this operation, be sure to hold the windshield glass using suction cups.

      Tech Tips


      • Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.

      • Depending on the vehicle, either 1 or 2 windshield retainers may be present.

    9. Using suction cups, remove the windshield glass sub-assembly.

      Note


      • Be careful not to drop the windshield glass sub-assembly.

      • Leave as much adhesive on the vehicle body as possible when removing the windshield glass sub-assembly.

  26. REMOVE WINDSHIELD GLASS ADHESIVE DAM


    1. When reusing the windshield glass:


      1. B000NETE01
        Text in Illustration
        *A Back Side

        Using a scraper, remove the windshield glass adhesive dam.

        Note


        • Be careful not to damage the windshield glass.

        • Be sure to replace the window glass adhesive dam with a new one.

  27. REMOVE WINDSHIELD OUTSIDE MOULDING


    1. When reusing the windshield glass:


      1. B000I65E01
        Text in Illustration
        *A Back Side

        Using a scraper, remove the windshield outside moulding.

        Note


        • Be careful not to damage the windshield glass.

        • Be sure to replace the windshield outside moulding with a new one.

  28. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)


    1. When reusing the windshield glass:


      1. B000HL4E01
        Text in Illustration
        *A Back Side

        Using a scraper, remove the 2 No. 1 windshield glass stoppers.

        Note


        • Be careful not to damage the windshield glass.

        • Be sure to replace the 1-piece type No. 1 windshield glass stoppers with a new pair of 2-piece type No. 1 and No. 2 windshield glass stoppers.

  29. REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)


    1. When reusing the windshield glass:


      1. B000HL4E01
        Text in Illustration
        *A Back Side

        Using a scraper, remove the 2 No. 2 windshield glass stoppers.

        Note


        • Be careful not to damage the windshield glass.

        • Be sure to replace the No. 2 windshield glass stoppers with new ones.

  30. REMOVE WINDSHIELD GLASS RETAINER


    1. When reusing the windshield glass:


      1. B000KY5E01
        Text in Illustration
        *A Back Side

        Remove the 2 windshield glass retainers.

        Note


        • Be careful not to damage the windshield glass.

        • Be sure to replace the windshield glass retainers with new ones.

        Tech Tips

        Depending on the vehicle, either 1 or 2 windshield retainers may be present.

  31. REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)


    1. B000MEI

      Remove the 2 No. 1 windshield glass stoppers.

      Note

      Be sure to replace the No. 1 windshield glass stoppers with new ones.

  32. CLEAN WINDSHIELD GLASS


    1. When reusing the windshield glass:


      1. B000IXR

        Using a scraper, remove any adhesive dam and adhesive residue from the windshield glass.

        Note

        Be careful not to damage the windshield glass.

      2. Clean the outer circumference of the windshield glass with a non-residue solvent.

        Note


        • Do not touch the windshield glass surface after cleaning it.

        • Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.

  33. CLEAN VEHICLE BODY


    1. B000K9LE07
      Text in Illustration
      *1 Adhesive
      *2 Vehicle Body

      Clean and shape the contact surfaces of the vehicle body.


      1. Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.

        Note

        Be careful not to damage the vehicle body.

        Tech Tips

        Leave as much adhesive on the vehicle body as possible.

      2. Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

        Tech Tips

        Even if all the adhesive has been removed, clean the vehicle body.