REAR DOOR POWER WINDOW REGULATOR MOTOR (for TMC, TMMR Made) INSPECTION

INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (FOR TMC MADE)

1. 

   Text in Illustration

   *a	Component without harness connected (Power Window Regulator Motor Assembly LH)
   *b	Clockwise
   *c	Counterclockwise

   Apply positive (+) battery voltage to connector terminal 2.

   Note

   Do not apply positive (+) battery voltage to any terminals other than terminal 2 to avoid damaging the pulse sensor inside the motor.

2. Connect a ground lead to connector terminals 1 and 7 or 10.

3. Check that the motor gear rotates smoothly as follows:

   OK

   Measurement Condition Specified Condition Connect a positive (+) battery lead to terminal 2, connect a negative (-) battery lead to terminal 1, and keep them connected for 3 seconds or more. With terminals 2 and 1 connected, connect a negative (-) battery lead to terminal 10. Disconnect and reconnect the negative (-) battery lead for terminal 10 within 1 second. Motor gear rotates clockwise Connect a positive (+) battery lead to terminal 2, connect a negative (-) battery lead to terminal 1, and keep them connected for 3 seconds or more. With terminals 2 and 1 connected, connect a negative (-) battery lead to terminal 7. Disconnect and reconnect the negative (-) battery lead for terminal 7 within 1 second. Motor gear rotates counterclockwise

   
   

   • If the result is not as specified, replace the power window regulator motor assembly LH.

   Note

   Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (FOR TMMR MADE)

1. 

   Text in Illustration

   *a	Component without harness connected (Power Window Regulator Motor Assembly LH)
   *b	Clockwise
   *c	Counterclockwise
   *d	Motor Gear

   Apply positive (+) battery voltage to connector terminal 2.

   Note

   Do not apply positive (+) battery voltage to any terminals other than terminal 2 to avoid damaging the pulse sensor inside the motor.

2. Connect a ground lead to connector terminals 1 and 7 or 10.

3. Check that the motor gear rotates smoothly as follows:

   OK

   Measurement Condition Specified Condition Connect a positive (+) battery lead to terminal 2, connect a negative (-) battery lead to terminal 1, and keep them connected for 3 seconds or more. With terminals 2 and 1 connected, connect a negative (-) battery lead to terminal 10. Motor gear rotates clockwise Connect a positive (+) battery lead to terminal 2, connect a negative (-) battery lead to terminal 1, and keep them connected for 3 seconds or more. With terminals 2 and 1 connected, connect a negative (-) battery lead to terminal 7. Motor gear rotates counterclockwise

   
   

   • If the result is not as specified, replace the power window regulator motor assembly LH.

   Note

   Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FOR TMC MADE)

1. 

   Text in Illustration

   *a	Component without harness connected (Power Window Regulator Motor Assembly RH)
   *b	Counterclockwise
   *c	Clockwise

   Apply positive (+) battery voltage to connector terminal 2.

   Note

   Do not apply positive (+) battery voltage to any terminals other than terminal 2 to avoid damaging the pulse sensor inside the motor.

2. Connect a ground lead to connector terminals 1 and 7 or 10.

3. Check that the motor gear rotates smoothly as follows:

   OK

   Measurement Condition Specified Condition Connect a positive (+) battery lead to terminal 2, connect a negative (-) battery lead to terminal 1, and keep them connected for 3 seconds or more. With terminals 2 and 1 connected, connect a negative (-) battery lead to terminal 10. Disconnect and reconnect the negative (-) battery lead for terminal 10 within 1 second. Motor gear rotates counterclockwise Connect a positive (+) battery lead to terminal 2, connect the negative (-) battery lead to terminal 1, and keep them connected for 3 seconds or more. With terminals 2 and 1 connected, connect a negative (-) battery lead to terminal 7. Disconnect and reconnect the negative (-) battery lead for terminal 7 within 1 second. Motor gear rotates clockwise

   
   

   • If the result is not as specified, replace the power window regulator motor assembly RH.

   Note

   Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.

INSPECT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (FOR TMMR MADE)

1. 

   Text in Illustration

   *a	Component without harness connected (Power Window Regulator Motor Assembly RH)
   *b	Clockwise
   *c	Counterclockwise
   *d	Motor Gear

   Apply positive (+) battery voltage to connector terminal 2.

   Note

   Do not apply positive (+) battery voltage to any terminals other than terminal 2 to avoid damaging the pulse sensor inside the motor.

2. Connect a ground lead to connector terminals 1 and 7 or 10.

3. Check that the motor gear rotates smoothly as follows:

   OK

   Measurement Condition Specified Condition Connect a positive (+) battery lead to terminal 2, connect a negative (-) battery lead to terminal 1, and keep them connected for 3 seconds or more. With terminals 2 and 1 connected, connect a negative (-) battery lead to terminal 10. Motor gear rotates counterclockwise Connect a positive (+) battery lead to terminal 2, connect the negative (-) battery lead to terminal 1, and keep them connected for 3 seconds or more. With terminals 2 and 1 connected, connect a negative (-) battery lead to terminal 7. Motor gear rotates clockwise

   
   

   • If the result is not as specified, replace the power window regulator motor assembly RH.

   Note

   Reset the power window regulator motor (initialize the pulse sensor) after installing the power window regulator motor and regulator assembly onto the door.