REAR DOOR POWER WINDOW REGULATOR MOTOR (for TMC, TMMR Made) REMOVAL

Tech Tips


  • Use the same procedure for both the RH and LH sides.

  • The procedure described below is for the LH side.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. B000NDR

      Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.

  4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. B000I33

      Using a moulding remover, disengage the 2 clips, 5 claws and 4 guides as shown in the illustration.

    2. w/o Seat Heater System:


      1. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

    3. w/ Seat Heater System:


      1. Disconnect the 2 connectors and remove the rear power window regulator switch assembly with rear door armrest base panel.

  5. REMOVE REAR ARMREST ASSEMBLY


    1. B000LSK

      Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. B000JX3E01
      Text in Illustration
      *1 Protective Tape

      Put protective tape around the rear door panel.

    2. B000I2D

      Remove the 3 screws.

    3. Using a clip remover, disengage the 8 clips.

    4. B000JHIE01
      Text in Illustration
      *1 Reference Boss
      *2 Rear Door Inner Glass Weatherstrip

      Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    5. Disengage the reference boss from the rear door panel.

    6. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

    7. B000ITM

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    8. Disconnect the connector.

    9. B000HNNE01
      Text in Illustration
      *1 Screwdriver

      Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.

  7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. B000ND9E01
      Text in Illustration
      *1 Screwdriver

      Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.

  8. REMOVE REAR DOOR SERVICE HOLE COVER


    1. B000IV7

      Disconnect the connector and remove the rear door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the door.

  9. DISCONNECT REAR DOOR WEATHERSTRIP


    1. B000MMQ

      Disconnect the upper part of rear door weatherstrip as shown in the illustration.

  10. REMOVE REAR DOOR GLASS RUN


    1. B000MBM

      Remove the rear door glass run.

  11. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. B000MZL

      Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.

      Note

      When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.

  12. REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. B000JAB

      Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. B000JWW

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the door glass.

  14. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY


    1. B000KAVE01
      Text in Illustration
      *1 Temporary Bolt

      Disconnect the connector.

    2. Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.

    3. Remove the 3 bolts.

    4. Remove the rear door window regulator assembly.

    5. Remove the temporary bolt from the rear door window regulator assembly.

  15. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. B000H7L

      Using a T25 "TORX" socket wrench, remove the 3 screws and rear power window regulator motor assembly.