REAR DOOR POWER WINDOW REGULATOR MOTOR (for TMMK Made) INSTALLATION

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY

    Note

    The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.


    1. B000H7L

      Using a T25 "TORX" socket wrench, install the rear power window regulator motor assembly with the 3 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Tech Tips

      When replacing a rear power window regulator motor assembly, a new rear power window regulator motor assembly uses self-tapping screws to thread new installation holes when the self-tapping screws are installed.

  3. INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY


    1. Apply MP grease to the sliding parts of the rear door window regulator assembly.

    2. Temporarily install the temporary bolt to the rear door window regulator assembly.

    3. B000KAVE04
      Text in Illustration
      *a Temporary Bolt

      Temporarily install the rear door window regulator assembly with the 3 bolts.

    4. Tighten the temporary bolt and 3 bolts to install the rear door window regulator assembly.

      Tech Tips

      Tighten the bolts in the order shown in the illustration.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  4. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. B000MWR

      Slide the rear door glass sub-assembly to install it as shown in the illustration.

      Note

      Do not damage the rear door glass sub-assembly.

  5. INSTALL REAR DOOR QUARTER WINDOW GLASS


    1. B000NBK

      Install the rear door quarter window glass as shown in the illustration.

  6. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. B000JOA

      Install the rear door lower window frame sub-assembly with the screw and 2 bolts.

  7. INSTALL REAR DOOR GLASS RUN


    1. B000NHF

      Install the rear door glass run.

  8. CONNECT REAR DOOR WEATHERSTRIP


    1. B000MDX

      Connect the upper part of rear door weatherstrip as shown in the illustration.

  9. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply new butyl tape to the rear door panel.

    2. B000HLLE01
      Text in Illustration
      *a Reference Point

      Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.

    3. Install the rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Connect the connector.

  10. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    1. B000HBK

      Install the rear door inner glass weatherstrip.

  11. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. B000NM3

      Install the No. 1 door scuff plate clamp as shown in the illustration.

    2. B000LP3E01
      Text in Illustration
      *1 Rear Door Inside Locking Cable Assembly
      *2 Rear Door Lock Remote Control Cable Assembly

      Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.

    3. B000HD1E01
      Text in Illustration
      *a Reference Boss

      Engage the 4 claws and reference boss as shown in the illustration.

    4. B000MQU

      Engage the 8 clips to install the rear door trim board sub-assembly.

    5. Install the 3 screws.

  12. INSTALL REAR ARMREST ASSEMBLY


    1. B000KAY

      Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.

  13. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. B000KGX

      Engage the 3 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.

  14. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. B000J18

      Engage the 3 claws to install the rear door inside handle bezel plug.

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  16. INSPECT POWER WINDOW OPERATION

    Click here