POWER WINDOW CONTROL SYSTEM (for Models with Jam Protection Function on 4 Windows) INITIALIZATION


  1. INITIALIZE POWER WINDOW CONTROL SYSTEM (POWER WINDOW REGULATOR MOTOR ASSEMBLY (ALL DOORS)) (EXCEPT TMMR MADE)

    Note


    • When a door window regulator assembly, power window regulator motor assembly, door glass or door glass run is reinstalled or replaced, the power window control system must be initialized. Functions such as the auto up and down, jam protection, remote control and key-off operation will not operate if initialization is not performed.

    • When a power window regulator motor assembly is replaced, DTC B2313 is stored. Clear the DTC after initialization Click here.

    • When performing initialization, do not perform any other procedures.

    • When performing initialization, use the power window switch of each door to initialize each door window.

    • If initialization is not completed properly, the LIN communication system may have a malfunction Click here.

    • Make sure to park the vehicle and turn off all the electrical systems before performing initialization. Initialization will be canceled if the vehicle is driven during initialization.

    • Make sure not to hit, strike or vibrate the door window glass during initialization because the vehicle is learning the sliding resistance of the door window glass.

    • Make sure not to turn the ignition switch to ON or off during initialization.

    Tech Tips

    If the battery has been replaced, it is not necessary to initialize the power window regulator motor assembly.


    1. Perform initialization according to the table below.

      Condition of Power Window Proceed to
      Initialization method when a power window regulator motor assembly has been replaced with a new one. Procedure A

      Initialization method when a power window regulator motor assembly has been removed/installed or a door glass and/or door glass run etc. have been removed/installed or replaced with new ones.

      Tech Tips

      Use this procedure if the power window regulator motor assembly has been reused.

      		 Procedure B
      Initialization method when a reverse rotation malfunction occurs due to a sliding resistance change resulting from adjustment etc. Procedure C

    2. Procedure A


      1. Connect the battery and turn the ignition switch ON.

      2. Fully open the power window by fully pushing down the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly, and hold the switch for 1 second or more after the window is fully opened.

      3. Fully close the power window by fully pulling up the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly, and hold the switch for 1 second or more after the power window is fully closed to reset the glass position and complete initialization.

    3. Procedure B


      1. Connect the battery and turn the ignition switch to ON.

      2. Fully close the power window by fully pulling up the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly, and hold the switch for 6 seconds or more after the window is fully closed (if the power window does not move or stops halfway even when the switch is fully pulled up, release the switch and fully pull it again).

      3. Fully open the window by pushing down the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly, and hold the switch for 1 second or more after the window is fully opened.

      4. Release the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly. Then fully push down and hold the switch for 4 seconds or more.

      5. Fully close the power window by fully pulling up the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly, and hold the switch for 1 second or more after the window is fully closed to reset the glass position and complete initialization.

    4. Procedure C


      1. Connect the battery and turn the ignition switch to ON.

      2. Fully open the window by fully pushing down the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly, and hold the switch for 1 second or more after the window is fully opened.

      3. Fully close the power window by fully pulling up the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly, and hold the switch for 1 second or more after the window is fully closed to reset the glass position and complete initialization.

  2. INITIALIZE POWER WINDOW CONTROL SYSTEM (ALL DOORS) (FOR TMMR MADE)

    Note


    • When a door window regulator assembly, power window regulator motor assembly, door glass or door glass run is reinstalled or replaced, the power window control system must be initialized. Functions such as the auto up and down function, jam protection function, catch protection function, remote control function, key-off operation function, key-linked function and wireless transmitter-linked function will not operate if initialization is not performed.

    • When a power window regulator motor assembly is replaced, DTC B2313 is stored. Clear the DTC after initialization Click here.

    • When performing initialization, do not perform any other procedures.

    • When performing initialization, use the power window switch of each door to initialize each door window.

    • If initialization does not complete properly, the LIN communication system may be malfunctioning. Click here.

    • Make sure to park the vehicle and turn off all electrical systems before performing initialization. Initialization will be canceled if the vehicle is driven during initialization.

    • Make sure not to hit, strike or vibrate the door window glass during initialization because the vehicle is learning the sliding resistance of the door window glass.

    • Make sure not to turn the engine switch on (IG) or off during initialization.

    Tech Tips

    If the battery has been replaced, it is not necessary to initialize the power window regulator motor assemblies.


    1. Perform initialization according to the table below.

      Condition of Power Window Proceed to
      Initialization method when a power window regulator motor assembly has been replaced with a new one. Procedure A

      • Initialization method for when a power window regulator motor assembly has been removed/installed or a door glass and/or door glass run, etc. have been removed/installed or replaced with new ones.

      • Initialization method for when the window cannot fully open via a down operation (door glass remains visible).

      • Initialization method for when the door glass cannot be fully closed (erroneously operates in reverse) after initialization.

      • Initialization method for when the door glass cannot be fully opened (erroneously stops) after initialization.

      • Initialization method for when instructions to perform initialization appear in other troubleshooting flowcharts.

      Tech Tips

      Use this procedure if a power window regulator motor assembly is being reused.

      		 Procedure B
      Initialization method for when the power window unexpectedly operates in reverse or stops due to a change in the sliding resistance after a fitting adjustment is made. Procedure C

    2. Procedure A

      Perform registration of the door glass position (fully closed, fully open) and sliding resistance learning.

      B000KPME12

      Tech Tips

      *: Even if the door glass is in the fully open position before performing step 3, perform the down operation for 1 second or more.

    3. Procedure B

      Reset the door glass position, perform window position initialization (fully closed, fully open) and sliding resistance learning.

      B000J1EE07
      B000MPLE11

      Tech Tips


      • *1: The door glass stopped position is the fully open position stored in the ECU.

      • *2: After performing step 7, release the switch, and then perform an auto down operation.

      • *3: After completing initialization, check that the power window can be fully closed using an auto up operation.

      • If the initialization is not completed properly, the LIN communication system may be malfunctioning Click here.

    4. Procedure C

      Perform sliding resistance learning.

      B000MV2E12

      Tech Tips


      • *: Do not release the switch during step 4, 5 or 6.

      • If the jam protection function or catch protection function continue to operate even after performing steps 4, 5 and 6, perform the procedure again from step 3.