INSTRUMENT PANEL SAFETY PAD (for TMMK Made) REMOVAL


  1. PRECAUTION

    Click here

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR SCUFF PLATE LH


    1. B000JR7E01

      Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.

    2. Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.

    3. Disengage the 6 claws (C) to remove the front door scuff plate LH.

  4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. B000MCM

      Remove the clip.

    2. Pull the cowl side trim sub-assembly LH as shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. B000KDO

      Disconnect the front door opening trim weatherstrip LH.

  6. REMOVE INSTRUMENT SIDE PANEL LH


    1. B000H81

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. B000IQ4

      Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

  7. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. B000HO0

      Disengage the 3 clips to remove the No. 1 instrument cluster finish panel garnish as shown in the illustration.

  8. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B000M8R

      Apply protective tape to the area shown in the illustration.

      Text in Illustration
      B000JL5 Protective Tape
    2. B000HAB

      Disengage the 2 clips as shown in the illustration.

    3. B000HMM

      Using a moulding remover, disengage the 2 clips to remove the No. 1 instrument panel register assembly.

  9. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.

    2. B000L6J

      Using a moulding remover, disengage the 2 claws, 4 clips and 2 guides.

    3. B000NP0

      Disengage the 5 claws, 5 clips and 2 guides.

    4. Disconnect each connector.

    5. B000I7Y

      Remove the instrument cluster finish panel assembly as shown in the illustration.

  10. REMOVE COMBINATION METER ASSEMBLY


    1. B000I9P

      Remove the 4 screws.

    2. B000LWI

      Disengage the wire harness clamp.

    3. Disconnect the 2 connectors to remove the combination meter assembly.

  11. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. B000H4N

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  12. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. B000M0W

      Remove the bolt <B> and screw <C> or <D>.

    2. B000HTR

      Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.

  13. REMOVE UPPER CONSOLE BOX SUB-ASSEMBLY


    1. B000NK9

      Disengage the 4 clips and remove the upper console box sub-assembly.

    2. w/ Seat Heater System:


      1. Disconnect each connector.

  14. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. B000JA9

      Disengage the 2 claws as shown in the illustration.

    2. B000NQD

      Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.

  15. REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY


    1. Move the shift lever to N.

    2. B000MQT

      Disconnect the connector.

    3. Remove the 2 screws <C> or <D>.

    4. B000MVY

      Disengage the 6 clips and remove the rear console upper panel sub-assembly.

  16. REMOVE CONSOLE BOX CUP HOLDER


    1. B000JJE

      Remove the console box cup holder from the rear console upper panel sub-assembly.

  17. REMOVE INSTRUMENT PANEL CUP HOLDER TRAY


    1. B000L7X

      Remove the 6 screws <E> and instrument panel cup holder tray.

    2. Remove the front console upper panel garnish.

  18. REMOVE NO. 4 CONSOLE BOX DUCT


    1. B000MX2

      Disengage the claw and remove the No. 4 console box duct.

  19. REMOVE CONSOLE BOX CARPET


    1. B000IH1

      Remove the console box carpet.

  20. REMOVE REAR CONSOLE BOX ASSEMBLY


    1. B000HIU

      Disconnect the connector and disengage the clamp.

    2. B000NQU

      Remove the 2 bolts and 2 screws.

    3. B000I0X

      Pull the rear console box assembly in the direction indicated by the arrow to disengage the 4 guides and remove the rear console box assembly.

  21. REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY


    1. B000IYK

      Using a moulding remover, disengage the 11 clips as shown in the illustration.

    2. Disconnect the connector to remove the No. 1 speaker opening cover assembly.

  22. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. B000IBG

      Remove the 2 screws <C> or <D>.

    2. B000IK8

      Disengage the 2 clips and guide as shown in the illustration.

    3. Disconnect each connector to remove the upper console panel sub-assembly.

  23. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)


    1. B000KA1E01
      Text in Illustration
      *a Protective Tape

      Apply protective tape to the areas shown in the illustration.

    2. B000JQL

      Remove the 4 bolts and 2 screws.

    3. B000MC7

      Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle to disengage the 4 clips.

    4. Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.

  24. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System)


    1. B000IZQE01
      Text in Illustration
      *a Protective Tape

      Apply protective tape to the areas shown in the illustration.

    2. B000M8B

      Remove the 4 bolts and 2 screws.

    3. B000LKD

      Pull the navigation receiver assembly with air conditioning control assembly toward the rear of the vehicle to disengage the 4 clips.

    4. Disconnect each connector and remove the navigation receiver assembly with air conditioning control assembly.

  25. REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)

    Note

    Do not touch the speaker cone.


    1. B000I7L

      Remove the 2 screws.

    2. Lift the front No. 3 speaker assembly and disconnect the connector to remove the speaker.

  26. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  27. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  28. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. B000IRZ

      Disconnect the front door opening trim weatherstrip RH.

  29. REMOVE INSTRUMENT SIDE PANEL RH


    1. B000MI2

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. B000J5U

      Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.

  30. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. B000LGW

      Disengage the 4 claws.

    2. Disengage the 2 guides.

    3. Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.

  31. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    CAUTION:

    When storing the lower No. 2 instrument panel airbag assembly, keep the airbag deployment side facing upward.


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. B000IIT

      Remove the 3 bolts.

    4. B000IF5

      Disengage the 3 claws to remove the lower No. 2 instrument panel airbag assembly.

      Note

      When removing the lower No. 2 instrument panel airbag assembly, do not pull the airbag wire harness.

    5. B000JCLE01
      Text in Illustration
      *1 Protective Tape
      *2 Airbag Connector
      *3 Airbag Connector Lock

      Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.

    6. Disconnect the airbag connector to remove the lower No. 2 instrument panel airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  32. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. B000MLZ

      Remove the 2 screws <C> or <D>.

    2. Open the lower instrument panel door.

    3. B000LE0

      Remove the 3 screws <C> or <D>.

    4. B000HGF

      Disengage the 2 clips and guide as shown in the illustration.

    5. B000KOB

      Disengage the clamp.

    6. Disengage the glove compartment light as shown in the illustration.

    7. Disconnect the connector and remove the lower instrument panel sub-assembly.

  33. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. B000K0Q

      Disengage the 5 clips to remove the No. 2 instrument cluster finish panel garnish as shown in the illustration.

  34. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B000M1F

      Apply protective tape to the area shown in the illustration.

      Text in Illustration
      B000JL5 Protective Tape
    2. B000KTZ

      Disengage the 2 clips as shown in the illustration.

    3. B000N9I

      Using a moulding remover, disengage the 2 clips to remove the No. 3 instrument panel register assembly.

  35. REMOVE FRONT PILLAR GARNISH LH


    1. B000I6YE01
      Text in Illustration
      *1 Front Pillar Garnish Clip

      Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

      Tech Tips

      Make the front pillar garnish LH hang from the front pillar garnish clip.

    2. B000K0CE02

      While pushing the tabs of the front pillar garnish clip in the direction indicated by the arrows (A) shown in the illustration, disengage the front pillar garnish clip.

      Note

      Do not apply excessive force using a tool.

    3. Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.

    4. Remove the 2 clips from the front pillar garnish LH.

    5. B000KY7E02
      Text in Illustration
      *1 Curtain Shield Airbag Assembly LH
      *a Protective Cover
      B000JL5 Adhesive Tape

      Protect the curtain shield airbag assembly LH.


      1. Cover the curtain shield airbag assembly LH with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

        Note

        Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.

  36. REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. B000HLK

      Apply protective tape to the area shown in the illustration.

      Text in Illustration
      B000JL5 Protective Tape
    2. B000I0I

      Using a moulding remover, disengage the 2 clips and 3 claws.

    3. Disengage the 2 guides to remove the No. 1 instrument panel speaker panel sub-assembly.

  37. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

    Note

    Do not touch the speaker cone.


    1. B000I7F

      Remove the 2 screws.

    2. Lift the front No. 2 speaker assembly and disconnect the connector to remove the speaker.

  38. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side Click here.

  39. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY


    1. B000H2W

      Apply protective tape to the area shown in the illustration.

      Text in Illustration
      B000JL5 Protective Tape
    2. B000M1Y

      Using a moulding remover, disengage the 2 clips and 3 claws.

    3. Disengage the 2 guides to remove the No. 2 instrument panel speaker panel sub-assembly.

  40. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

    Tech Tips

    Use the same procedure as for the LH side Click here.

  41. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. B000HKC

      Disengage the 4 clips and guide.

    2. Disconnect the connector to remove the lower instrument panel finish panel assembly.

  42. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. B000MRC

      Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.

    2. B000I5A

      Remove the screw <C> or <D>.

    3. B000JK3

      Disengage the 2 clips and guide to remove the front No. 2 console box insert as shown in the illustration.

  43. REMOVE CONSOLE BOX INSERT


    1. B000K6Y

      Remove the screw <C> or <D>.

    2. B000HST

      Disengage the 2 clips and guide to remove the console box insert as shown in the illustration.

  44. REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY


    1. Disengage the 10 clips to remove the No. 1 instrument panel garnish sub-assembly as shown in the illustration.

      B000KS6

  45. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE


    1. Check that the engine switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. B000ILJE01
      Text in Illustration
      *a Slider

      Slide the slider to release the lock, and then disconnect the connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  46. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY


    1. B000KDR

      Remove the 2 bolts <B>.

    2. Disengage the clamp to remove the radio tuner mounting bracket.

    3. Disconnect each connector.

      B000I78

    4. Disengage each clamp.

    5. Remove the 2 passenger airbag bolts <A>.

      B000IRDE01
      Text in Illustration
      *a Passenger Airbag Bolt <A> *b Bolt <B>
      *c Nut <F> or <G> *d Clip

    6. Remove the 3 bolts <B> and nut <F> or <G>.

    7. Remove the 2 clips.

    8. Disengage the 5 guides and remove the instrument panel safety pad assembly as shown in the illustration.

      B000M7Y

      Note


      • Do not damage the instrument panel safety pad assembly.

      • Do not allow the wire harnesses to interfere with the surrounding parts.