AIR CONDITIONING PANEL (for TMC, TMMR Made) REMOVAL


  1. PRECAUTION (w/ Navigation System)

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Navigation System)

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT PANEL GARNISH LH


    1. B000IYJ

      Disengage the 3 clips and 8 guides to remove the front panel garnish LH as shown in the illustration.

  4. REMOVE FRONT PANEL GARNISH RH


    1. B000MWG

      Disengage the 3 clips and 8 guides to remove the front panel garnish RH.

  5. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY


    1. B000MRZ

      Using a moulding remover, pry up on the center instrument cluster finish panel sub-assembly until there is enough of a gap to make it possible to pull on the panel by hand.

    2. B000LY7

      Pull the center instrument cluster finish panel sub-assembly in the direction indicated by the arrow to disengage the 7 clips and 2 guides to remove the center instrument cluster finish panel sub-assembly as shown in the illustration.

  6. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. B000HHL

      Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 4 clips as shown in the illustration.

    2. Disconnect the connector to remove the No. 2 instrument panel register assembly.

  7. REMOVE FRONT CONSOLE UPPER PANEL GARNISH


    1. for Blank Type:


      1. B000K2U

        Disengage the 2 claws and remove the front console upper panel garnish as shown in the illustration.

    2. for 3 Switch Hole Type:


      1. B000MPF

        Disengage the 2 claws as shown in the illustration.

      2. Disconnect the each connector to remove the front console upper panel garnish.

  8. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Radio Receiver Type)


    1. B000K9KE01
      Text in Illustration
      *a Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. B000NM6

      Remove the 4 bolts.

    3. B000H0V

      Pull the radio receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 6 clips.

    4. Disconnect each connector and remove the radio receiver assembly with air conditioning control assembly.

  9. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (for Navigation Receiver Type)


    1. B000I3PE01
      Text in Illustration
      *a Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. B000KTH

      Remove the 4 bolts.

    3. B000K9D

      Pull the navigation receiver assembly with air conditioning control assembly toward the rear of the vehicle and disengage the 6 clips.

    4. Disconnect each connector and remove the navigation receiver assembly with air conditioning control assembly.

  10. REMOVE NO. 1 RADIO BRACKET (for Radio Receiver Type)


    1. w/o Navigation System:


      1. B000IA1

        Remove the 4 screws and No. 1 radio bracket.

    2. w/ Navigation System:


      1. B000IQ9

        Remove the 6 screws and No. 1 radio bracket.

  11. REMOVE NO. 2 RADIO BRACKET (for Radio Receiver Type)


    1. w/o Navigation System:


      1. B000JC3

        Remove the 4 screws and No. 2 radio bracket.

    2. w/ Navigation System:


      1. B000L32

        Remove the 6 screws and No. 2 radio bracket.

  12. REMOVE NO. 1 RADIO BRACKET (for Navigation Receiver Type)


    1. B000IFO

      Remove the 4 screws and No. 1 radio bracket.

  13. REMOVE NO. 2 RADIO BRACKET (for Navigation Receiver Type)


    1. B000J89

      Remove the 4 screws and No. 2 radio bracket.

  14. REMOVE AIR CONDITIONING CONTROL ASSEMBLY


    1. B000IGU

      Disengage the 4 clips and remove the air conditioning control assembly.